Which tool installs this fastener?
Enter a fastener part number for the exact nose or pulling head at its diameter, the tools that take it and any adapters, from each tool maker's catalog. Or enter a tool, nose or adapter PN to see what it installs across brands. Cross-brand fits are shown only where a catalog states them; everything else reads "not documented".
Try CR3213-6-02 · HC3213-6-02 · AF3213-6-02 · NAS1446-10 · MBF2110-6-300 · HL10-6-8 · H701B-456 · G83A
Tooling for MS21047-3
MS21047-3 (Self-locking nutplates (MS21047, MS21059, MS21069, MS21078; rivetless ForceTec), 3/32"): the process document lists these tools for this size.
- Nutplate drill motorDrill motor that drills both rivet holes at onceFAA-H-8083-31B p.4-15 ↗
- ForceTec mandrel and split sleeveMandrel / sleeve assembly (ForceTec)FTI ForceTec brochure p.4 ↗
- ForceTec Right Angle PullerRight Angle Puller "for holes in pockets or areas with limited front-side access"FTI ForceTec brochure p.4 ↗
- ForceTec Offset AdapterOffset Adapter "for installs in tight and restricted areas"FTI ForceTec brochure p.4 ↗
- ForceTec Hand PullerHand Puller "for quick field service installations"FTI ForceTec brochure p.4 ↗
No per-size tool and nose table is on file for this family: see Sources.
Self-locking nutplates (MS21047, MS21059, MS21069, MS21078; rivetless ForceTec) tool tables
Sources2
- FAA-H-8083-31B (AMT Handbook, Airframe), p.4-15, Nutplate drill ↗
- "Special drill motors that drill two holes at the same time are used for the installation of nutplates. By drilling two holes at the same time, the distance between the holes is fixed and the holes line up perfectly with the holes in the nutplate." No part number is given.
- FTI ForceTec brochure, p.4, ForceTec Installation Procedure; Special Installations; Trimming Tools ↗
- Steps: "Slide the split sleeve onto the mandrel"; "Insert the mandrel/sleeve assembly through the retainer"; "Activate the hydraulic puller unit". FTI "also offers a sleeveless method and an accelerated installation method".
Not documented
- The Self-locking nutplates (MS21047, MS21059, MS21069, MS21078; rivetless ForceTec) process document names tools for this size but prints no per-size tool and nose (adaptor) table: No published tool-by-size table: the MS sheets size the rivet holes but name neither rivet nor tool, and FTI's ForceTec tool numbers are behind its technical library login..
Diameter -3 (3/32"): decoded from the part number.
Tool catalogs are the manufacturers' as published in the cited edition; confirm current PNs with the tool maker before purchase. Install per the OEM process specification.
Compatibility matrixNose by fastener, brand and diameter
Each cell lists the noses the brand's own catalog names for that fastener and diameter. A dash (–) means the fastener is not made in that diameter, per its catalog's size list. "Not documented" means the size exists, or its range is not on file, and no catalog on file names a nose for it, not that none exists. Gage Bilt states its tools and noses are interchangeable with Huck, Cherry and Allfast; its cross-reference (on each tool page) gives its PN for each Huck or Cherry PN. Allfast tooling is a gap until an Allfast tool catalog is on file. A NAS93xx blind rivet's tooling follows its maker: the Cherry cells are for Cherry-made parts, the Huck cells for Huck-made (HuckMAX™, HUCK-CLINCH®). NAS lockbolt cells name the standard itself.
Reference only: the controlling drawing, its process spec and the manufacturer's installation instructions govern. How to use these answers
Next step
Free to ask. A person at SpecLok replies by email. You only pay the supplier if you accept a quote.