← Tooling compatibility finder
H753A-456
H753A-456 Right Angle Pulling Head · Nose / pulling head · Cherry · Right angle
H753A-456 installs CherryMAX® blind rivet -4, -5, -6 on a G704B, G747 or G800.
Catalog noteDetails
Traced from 2 manufacturer views, with published dimensions held fixed. Other shapes and unseen depths are inferred.
Built from 7 printed dimensions, 12 scaled from the figure.Details
Reference reconstruction traced from manufacturer views and constrained by printed dimensions. Undimensioned shapes and depths are inferred and labelled; omitted features mean this is not a guaranteed clearance boundary. NOT a manufacturing model or manufacturer CAD. Jaws and internal parts are not modelled. Verify fit and clearance against current manufacturer data and the physical tool.
- 2-7/8 Nose tip to the frame's back face · Cherry TS-H753A-456 instruction sheet (Rev E, 19 Dec 14), p.1, Fig. 1 Dimensional Data
- 2-1/4 Nose tip to the end of the head's top edge · Cherry TS-H753A-456 instruction sheet (Rev E, 19 Dec 14), p.1, Fig. 1 Dimensional Data
- 13/16 Nose tip to the jam nut's front face · Cherry TS-H753A-456 instruction sheet (Rev E, 19 Dec 14), p.1, Fig. 1 Dimensional Data
- 3/8 Fastener centreline to the top of the jam nut · Cherry TS-H753A-456 instruction sheet (Rev E, 19 Dec 14), p.1, Fig. 1 Dimensional Data
- 5/8 Nose sleeve diameter · Cherry TS-H753A-456 instruction sheet (Rev E, 19 Dec 14), p.1, Fig. 1 Dimensional Data
- 5-1/2 Top of the head to the mount jam nut's lower face · Cherry TS-H753A-456 instruction sheet (Rev E, 19 Dec 14), p.1, Fig. 1 Dimensional Data
- 13/16 Frame width (front view) · Cherry TS-H753A-456 instruction sheet (Rev E, 19 Dec 14), p.1, Fig. 1 Dimensional Data
Scaled from the catalog figure, not dimensioned
- Frame: side outline (length): 1.91 in (scaled from Cherry TS-H753A-456 instruction sheet (Rev E, 19 Dec 14) p.1, Fig. 1 Dimensional Data (Rev E), side view, not dimensioned)
- Pivot pin upper: diameter: 0.26 in (scaled from Cherry TS-H753A-456 instruction sheet (Rev E, 19 Dec 14) p.1, Fig. 1 Dimensional Data (Rev E), side view, not dimensioned)
- Pivot pin lower: diameter: 0.26 in (scaled from Cherry TS-H753A-456 instruction sheet (Rev E, 19 Dec 14) p.1, Fig. 1 Dimensional Data (Rev E), side view, not dimensioned)
- Mount adapter: side outline (length): 0.90 in (scaled from Cherry TS-H753A-456 instruction sheet (Rev E, 19 Dec 14) p.1, Fig. 1 Dimensional Data (Rev E), side view, not dimensioned)
- Mount adapter: width: 0.91 in (scaled from Cherry TS-H753A-456 instruction sheet (Rev E, 19 Dec 14) p.1, Fig. 1 Dimensional Data (Rev E), front view, not dimensioned)
- Mount collar: largest diameter: 0.77 in (scaled from Cherry TS-H753A-456 instruction sheet (Rev E, 19 Dec 14) p.1, Fig. 1 Dimensional Data (Rev E), side view, not dimensioned)
- Mount jam nut: across flats: 0.90 in (scaled from Cherry TS-H753A-456 instruction sheet (Rev E, 19 Dec 14) p.1, Fig. 1 Dimensional Data (Rev E), side view, not dimensioned)
- Mount thread: crest spacing (as drawn; not a thread specification): 0.03 in (scaled from Cherry TS-H753A-456 instruction sheet (Rev E, 19 Dec 14) p.1, Fig. 1 Dimensional Data (Rev E), side view, not dimensioned)
- Mount end ring: largest diameter: 0.70 in (scaled from Cherry TS-H753A-456 instruction sheet (Rev E, 19 Dec 14) p.1, Fig. 1 Dimensional Data (Rev E), side view, not dimensioned)
- Nose: largest diameter: 0.63 in (scaled from Cherry TS-H753A-456 instruction sheet (Rev E, 19 Dec 14) p.1, Fig. 1 Dimensional Data (Rev E), side view, not dimensioned)
- Nose thread: crest spacing (as drawn; not a thread specification): 0.04 in (scaled from Cherry TS-H753A-456 instruction sheet (Rev E, 19 Dec 14) p.1, Fig. 1 Dimensional Data (Rev E), side view, not dimensioned)
- Jam nut: across flats: 0.75 in (scaled from Cherry TS-H753A-456 instruction sheet (Rev E, 19 Dec 14) p.1, Fig. 1 Dimensional Data (Rev E), side view, not dimensioned)
- Built from the tool sheet's Fig. 1 (side and front views), not the catalog photo: the catalog's 5-7/16 and 2-1/4 are kept on the tool's page but not used here.
- Fastener axis horizontal, the nose tip to the left (-x) as the side view draws it; tool axis vertical through the mount, y = 0 at the mount jam nut's lower face (the 5-1/2's lower line), x = 0 at the frame's back face.
- Part names follow the tool sheet's p.2 parts list where the figure shows them (frame, nose, jam nut, adapter fitting at the mount).
Not modelled
Everything it installs1 fastener group
CherryMAX® blind rivet (NAS9301 to NAS9312 / CR3213 to CR3555P) -4, -5, -6, per the Cherry catalog
Fastener process documents that name it3
- CherryMAX -4, -5, -6 Cherry CA-1015 p.20 ↗
- Cherry Maxibolt -4, -5 Cherry CA-1015 p.20 ↗
- Cherry SST -4, -5, -6 Cherry CA-1015 p.20 ↗
Other brands' equivalents1 statement
- Gage Bilt says 456MAX-704-54RA replaces H753A-456 (Cherry) Gage Bilt 2017 p.156 ↗
Gage Bilt's cross-reference lists 456MAX-704-54RA (nose assembly - rt. angle) for H753A-456.
Sources6
- Cherry Fastening Systems for Aerospace Tool Catalog (©2015 edition, archived), p.26, CherryMAX® Blind Rivets & Tools, Cherry Power Tools ↗
- Inconel part: "NOTE: G704B/G83A/G84 power riveters recommended for installation of Inconel fasteners due to high break stem loads" (©2015 guide p.26). The G747 and G800 the same table lists are left off for Inconel.
- "*** Use adapter 680B205" (p.26). -4 and -5 only: CA-1015 p.5 does not shade -6 for the G784 with CherryMAX® heads, though p.26 and CA-1001 p.13 print -6; confirm with Cherry before using it at -6.
- Cherry CA-1001 Tool Catalog (2017), p.6, Pulling Heads table ↗
- Nominal diameters. Section 1 riveter with a Section 1 pulling head (CA-1001 p.1, p.6); CA-1015 p.5 shades nominal -4, -5, -6. The ©2015 CherryMAX guide (p.26) does not list the G746A.
- Cherry CA-1015 (CherryMAX process manual), p.5, CherryMAX® Tool Selection (shaded chart) ↗
- Oversize diameters: CA-1015 p.5 shades the G746A for oversize -4 and -5 only (not -6).
- Cherry CA-1001 Tool Catalog (2017), p.22, Riveter Adapters ↗
- 744-300: G83A, G84 to the G704B (CherryMAX®) mounting system "for H701B, H747, H781A, H782, H753A"; "Must remove the bayonet adapter".
- Cherry CA-1015 (CherryMAX process manual), p.20, Pulling Heads ↗
- Gage Bilt Aerospace Catalog 2017 (archived; pages are PDF pages), p.156, Other - Gage Bilt Cross Reference, page 51 ↗
Tool catalogs are the manufacturers' as published in the cited edition; confirm current PNs with the tool maker before purchase. Install per the OEM process specification.
Published dimensions13 · for envelope CAD
| Feature | Value | As printed | Source |
|---|---|---|---|
| Head reach (tool face to far side) | 5.4375 in | 5-7/16" | Cherry CA-1001 Tool Catalog (2017), p.6, H753A-456 drawing ↗ |
| Head height (tip to back) | 2.25 in | 2-1/4" | Cherry CA-1001 Tool Catalog (2017), p.6, H753A-456 drawing ↗ |
| As drawn (feature not labeled) | 0.375 in | 3/8" Drawn at the nose, from the end face of the head to a line at the nose. The catalog does not label the feature. | Cherry CA-1001 Tool Catalog (2017), p.6, H753A-456 drawing ↗ |
| As drawn (feature not labeled) | 2.875 in | 2-7/8 Side view: nose tip to the frame's back face. | Cherry TS-H753A-456 instruction sheet (Rev E, 19 Dec 14), p.1, Fig. 1 Dimensional Data ↗ |
| As drawn (feature not labeled) | 2.25 in | 2-1/4 Side view: nose tip to the end of the head's top edge. | Cherry TS-H753A-456 instruction sheet (Rev E, 19 Dec 14), p.1, Fig. 1 Dimensional Data ↗ |
| As drawn (feature not labeled) | 0.8125 in | 13/16 Side view: nose tip to the jam nut's front face (how far the nose stands out). | Cherry TS-H753A-456 instruction sheet (Rev E, 19 Dec 14), p.1, Fig. 1 Dimensional Data ↗ |
| As drawn (feature not labeled) | 0.375 in | 3/8 Side view: fastener centreline to the top of the jam nut. | Cherry TS-H753A-456 instruction sheet (Rev E, 19 Dec 14), p.1, Fig. 1 Dimensional Data ↗ |
| Nose diameter | 0.625 in | 5/8 Side view: the nose sleeve's diameter. | Cherry TS-H753A-456 instruction sheet (Rev E, 19 Dec 14), p.1, Fig. 1 Dimensional Data ↗ |
| As drawn (feature not labeled) | 5.5 in | 5-1/2 Side view: top of the head to the lower face of the mount's jam nut. | Cherry TS-H753A-456 instruction sheet (Rev E, 19 Dec 14), p.1, Fig. 1 Dimensional Data ↗ |
| Head width | 0.8125 in | 13/16 Front view: the frame's width. | Cherry TS-H753A-456 instruction sheet (Rev E, 19 Dec 14), p.1, Fig. 1 Dimensional Data ↗ |
As printed in the fastener process documents
- Length (as dimensioned): 5 7/16" (138,11 mm) (CherryMAX, Cherry Maxibolt, Cherry SST, Cherry CA-1015 (CherryMAX process manual), p.20, Pulling Heads ↗)
- Height (as dimensioned): 2 1/4" (57,15 mm) (CherryMAX, Cherry Maxibolt, Cherry SST, Cherry CA-1015 (CherryMAX process manual), p.20, Pulling Heads ↗)
- Nose (as dimensioned): 3/8" (9,53 mm) (CherryMAX, Cherry Maxibolt, Cherry SST, Cherry CA-1015 (CherryMAX process manual), p.20, Pulling Heads ↗)
Only dimensions a document prints are listed, with the feature each one measures. A length read from a part number by a rule the cited chart prints is marked "Not printed as a number". None of these catalogs publishes nose tip or anvil geometry detailed enough to machine from.
On the floor:Low clearance puller finderRight angle CherryMAX puller: heads and dimensions
Reference only: the controlling drawing, its process spec and the manufacturer's installation instructions govern. How to use these answers
Next step
Free to ask. A person at SpecLok replies by email. You only pay the supplier if you accept a quote.