Cherry, blind bolt
Cherry Maxibolt
Cherry MAXIBOLT pull-type blind bolt: MS90353/MS90354 and MS21140/MS21141 equivalents.

- Shear 95-112 ksi
- Access Blind (one-sided)
- Diameters 1/8 to 5/16"
- Materials Alloy steel, A286 CRES +1
- Lead-time risk Medium
Head style
Range source
CA-1009 p.3 · grip table. Bands use published limits; gaps remain visible. The near-edge check is SpecLok’s 20% threshold.
Blind (one-sided), pull-type blind bolt: “Installation shall be accomplished by the spindle being pulled into the sleeve, forming a blind head on the back side of the assembly,” (Cherry PS-CMB-7000 (Titanium MAXIBOLT), p.4 of 12, §3.4.1)
- Shear
- 95-112 ksi
- Blind bulb
- standard
- Install
- One-side install
- Diameters
- 1/8, 5/32, 3/16, 1/4, 5/16"
- Lead-time risk (SpecLok assessment)
- Medium
Typical applications
- ·Blind bolt callouts to MS90353/MS90354 or MS21140/MS21141 (CA-1009)
Strengths
- +Installed single shear 3,450 lb at -06, alloy steel (CA-1009)
- +MS90353/MS90354 (alloy steel) and MS21140/MS21141 (A-286) cross-references (CA-1009)
- +Titanium Maxibolt, 95 KSI (PS-CMB-7000)
Trade-offs
- −Cherry installation tooling and pulling heads (CA-1009)
Also called MaxiBolt, CR7000 series, high-strength blind bolt. P/N: CR7310 / CR7311 alloy steel (MS90353 / MS90354) · CR7620 / CR7621 A-286 (MS21140 / MS21141) · e.g. CR7310S-06-04 = MS90353S0604
Dimensions
| A | SLEEVE head diameter (flush: to the theoretical sharp edge; the model takes it through the H / W gage, under A Max.) | .386Max. |
| B | SLEEVE head height (flush: depth, derived at 100° and checked against B Max.) | .080Max. |
| D | SLEEVE shank diameter | .198±.001 |
| Z | STEM tail above the head top, min | .875Min. |
| Hole Limits | Hole limits | .199/.202 |
| Grip limits | Grip dash -05 (1/16 range) | .281-.345 |
All dimensions (18)Fewer dimensions
| Double Action | Type cell, double action (shifting) tool, no shift washer | -06 |
| Single Action S | Type cell, single action tool, supplied with shift washer (-08, -10 print here with no letter) | S06 |
| Single Action U | Type cell, single action tool, no shift washer | U06 |
| C | SLEEVE flush head land, max (not modelled: the edge is drawn sharp) | .013Max. |
| H | Flush head gage: depth below the head top where the cone is W across | .0205/.0243 |
| P | Length at the sleeve end over which D may be .002 undersize (note ①; not modelled) | .250Max. |
| R | Head-to-shank radius, max (not modelled) | .015Max. |
| W | Flush head gage diameter | .3270/.3272Gage |
| Single Shear | Installed single shear, lbs min | 3450Min. (lbs.) |
| Tensile | Installed tensile, lbs min | 2100Min. (lbs.) |
| L | SLEEVE length from the datum (flush: head top; protruding: bearing face) | .490Ref. |
| K | STEM blind end from the datum | .666Max. |
As printed on CA-1009 p.3 ↗. Letters match the drawing.
Printed in CA-1009 for CR7310-06-05
| Type | -06 (Double Action column): double action (shifting) tool, no shift washer (note ③ and the type cutaways) (CA-1009 p.3) |
|---|---|
| Sleeve | 4037 Alloy Steel ASTM-A-331; finish CAD. Plate QQ-P-416 Type II, Class 2 (CA-1009 p.3) |
| Stem | 8740 Alloy Steel ASTM-A-331; finish CAD. Plate QQ-P-416 Type I, Class 3 (CA-1009 p.3) |
| Lock collar | A-286 CRES AMS 5737 or 316 CRES AMS 5690; finish Passivate AMS 2700 (CA-1009 p.3) |
| Finish code | None (CA-1009 p.3) |
| Grip | .281 to .345 in (dash -05); L Ref. .490, K Max. .666 (CA-1009 p.3) |
| Hole limits | .199/.202 in (CA-1009 p.3) |
| Installed strength | Single shear 3450 lbs min, tensile 2100 lbs min (CA-1009 p.3) |
| Standard | ➅ This product meets the requirements of MS90353 (except for zinc plating and NAS 4006 Alum coating) for “-” code parts, in the -05, -06, -08, and -10 diameter series; and for “S” code parts in the S05 and S06 diameter series. (CA-1009 p.3) |
Datasheet strength: Installed single shear at -06: 3,450 lb (CR7310, alloy steel), 2,925 lb (CR7620, A-286): Cherry CA-1009. Titanium CR777x: 95 KSI (PS-CMB-7000).
Materials and galvanic compatibility vs CFRP
| Alloy | Shear (ksi) | vs CFRP | Notes | Source |
|---|---|---|---|---|
| Alloy steel | 112 | high | CR7310/CR7311 (MS90353/MS90354) | Derived: CA-1009 CR7310 single shear 3,450 lb at -06 ÷ D .198 area |
| A286 CRES | 95 | low | CR7620/CR7621 (MS21140/MS21141) | Derived: CA-1009 CR7620 installed single shear 2,925 lb at -06 ÷ D .198 area |
| Titanium | 95 | low | CR777x: CP Ti sleeve, Beta C stem (shift-washer type) | PS-CMB-7000 §1: 95 KSI |
vs CFRP: MIL-STD-889C Table I, graphite column: high = incompatible in marine atmosphere, sea water and industrial atmosphere; med = incompatible in marine atmosphere and sea water, compatible in industrial atmosphere (brass); low = compatible except sea water; unrated = not a Table I entry (non-metallic).About derived ksi
Specs source: Cherry CA-1009 (Maxibolt catalog) + PS-CMB-7000 (titanium) ↗: CR7310/7311/7620/7621 tables: dimensions, grip limits, installed single shear & tensile (lbf), MS cross-reference. Titanium: PS-CMB-7000 §1. Lead-time risk is SpecLok's sourcing assessment, not a datasheet value.
Section from Cherry CA-1009 ↗ p.3. Collar flange thickness scaled from the p.5 figure.Drawing notes
Model
Envelope model, not manufacturer CAD. Download STEP or STL from the part panel at the top.Model details
CR7310-06-05, manufacturer nominal. Simplified component model from Cherry CA-1009 p.3: one named solid per physical part (SLEEVE, STEM, LOCK COLLAR, and SHIFT WASHER on the types supplied with one). The sleeve's outside, L, Z, K, the .030 min gap and the stem head at D are printed (the flush head through its H / W gage at the printed 100°); the bore, head recess, stem detail, lock collar and shift washer are scaled from Cherry's own figures (p.2 section, p.3 and p.5 side views) and labelled. As supplied only: CA-1009 prints no installed dimensions. Not manufacturer CAD. Verify against the current catalog before use. Axis +Z, head up, z = 0 at the datum (flush head top, protruding bearing face). STEP (AP214) is in inches; STL in millimetres.
Source
- Cherry CA-1009 ↗ Cherry MAXIBOLT® Blind Bolts (catalog CA-1009).
- Numbering: Base (CR7310) + type letter (none, S or U, as the Dia. Dash No. columns print it) - diameter (05 = 5/32") - grip dash (1/16ths) + finish code (none for the None row), e.g. CR7310S-06-04, CR7310U-06-04D, CR7310-06-04 (CA-1009 p.3). The rivet number carries the type letter and the finish code. No part number pages for this family yet: the configurator only.
- Each physical part is its own solid, named as the document names it. What the document draws without a dimension is left out or, where the shape is needed, scaled from its figure (or taken from cited guidance) and labelled; see the drawing notes and the STEP header.
- CR7310: sleeve 4037 Alloy Steel ASTM-A-331 (CAD. Plate QQ-P-416 Type II, Class 2); stem 8740 Alloy Steel ASTM-A-331 (CAD. Plate QQ-P-416 Type I, Class 3). CA-1009 p.3.
- Every head style, rivet number, diameter and grip on the transcribed standards pages. The 3D view, the drawing and the STEP / STL download are all built from the printed dimension letters; nothing the catalog does not dimension is modelled.
CA-1009 p.3-10, manufacturer printed values.
Printed as is: 17 values in CA-1009 that look inconsistent
- p.5 grip table, -14, 06 Dia.: L Ref. is printed 1.503 with K Max. 1.229: a sleeve longer than its stem is impossible. The 1/16 progression gives 1.053, which CR7310, CR7341, CR7621 and CR7651 print in the same cell. CR7311-06-14 (every type and finish) is not offered by the configurator.
- p.4 dimension table, S04 B: Printed ". 042" with a space after the point; read as .042 (B is not used by the model).
- p.4 dimension table, -08 W: Printed ". 4318/.4320" with a space after the first point; read as .4318/.4320, as CR7310, CR7340 and CR7650 print the -08 gage.
- p.7 dimension table, S06 H: Printed "0205/.0243" without the leading point; read as .0205/.0243, as CR7310, CR7620 and CR7650 print the 06 gage H.
- p.8 dimension table, S06 W: Printed ".3270/3272" without the second point; read as .3270/.3272, as CR7310, CR7620 and CR7340 print the 06 gage W.
- p.10 grip table, -12, 10 Dia.: K Max. printed "1 .243" with a space; read as 1.243, as every other page prints this cell.
- p.8 grip table, -16, 05 Dia.: L Ref. and K Max. printed ". —" (a point, a space and a dash); read as not listed, as CR7310 and CR7340 print "—" there.
- p.4 grip table, -02, 06 Dia.: L Ref. .329 where CR7310, CR7311, CR7621, CR7341 and CR7651 print .303 (the 1/16 progression from -03 .365); K Max. .479 as elsewhere, so K - L is .150 against .176 in every other 06 row. Modelled as printed.
- p.7 grip table, -02, 06 Dia.: L Ref. .329 (see CR7620); K Max. .479. Modelled as printed.
- p.8 grip table, -02, 06 Dia.: L Ref. .329 and K Max. .505 where the other pages print K .479 (K - L .176 as in every other 06 row). Modelled as printed.
- p.4 grip table, -19, 06 Dia. and -20, 08 Dia.: L Ref. 1.366 (CR7310 and CR7311: 1.365) and 1.468 (CR7310 and CR7311: 1.469). Modelled as printed.
- p.5 grip table, -18 Max.: Grip limit max printed 1.157; the flush pages print 1.158 for -18. Used as printed.
- p.8 note ➄: "-06 dia. is .100"; CR7310, CR7620 and CR7340 note ➄ print .120. The configurator uses each page's own note.
- p.4 note 11: "Required on -05 dia. and larger with “none” or “P” finish code": its marker is not printed anywhere on the page (CR7621 note ➉ the same). Shown as printed, not applied.
- p.5 note 5: Cites MS90353 (the flush head standard) on the protruding head page; the p.11 interchangeability table and the part number examples pair CR7311 with MS90354.
- p.10 grip table, Grip Dash No.: Printed "-1" to "-9" where the other pages print "-01" to "-09".
- p.3 material table: Cells kept as printed, including "A-286-CRES" (EZ row), "Or" / "or" / "OR" and "OptionaL" (CR7620, CR7621, CR7650 P rows).
5 head styles
Some variants only partly sourcedNot redrawn: no head dimensions for this variant in the documents on file. The data at right is from the cited document.
100° flush head · 100°
- CR7310 · MS90353: Alloy steel
- CR7620 · MS21140: A-286 CRESCherry CA-1009 (MAXIBOLT), p.4 100° flush head, CR7620 ↗
- CR7340 · oversize: Alloy steelCherry CA-1009 (MAXIBOLT), p.7 oversize flush head, CR7340 ↗
- CR7650 · oversize: A-286 CRESCherry CA-1009 (MAXIBOLT), p.8 oversize flush head, CR7650 ↗
Source: Cherry CA-1009 (MAXIBOLT), p.3 100° flush head, CR7310 ↗
Titanium CR777x (PS-CMB-7000) is listed without a head style in the documents on file.
Head styles (manufacturer terms)
- 100° flush head (CR7310, CR7620, CR7340, CR7650)
- Protruding head (CR7311, CR7621, CR7341, CR7651, CR7683)
- 100° Flush Head (AN509) (CR7680)
- 100° Flush Head (MS20426) (CR7686)
- 130° Flush Head (CR7684, CR7784)
Pulled stem / bulbing · 3 steps
1/3Spindle pulled
“Installation shall be accomplished by the spindle being pulled into the sleeve,”
Cherry PS-CMB-7000 (Titanium MAXIBOLT), p.4 of 12, §3.4.1 ↗
Drawing traced from: Panel 1.
Source images (1): patent and government drawings
A patent drawing shows the patented design, which can differ in detail from today's catalog part. Each image says why it is tied to this family.

Installation verification and preload
Installed preload
- Alloy steel (MS90353/54), min tensile preload: 5/32": 135 lb · 3/16": 210 lb · 1/4": 365 lb · 5/16": 520 lb (MIL-F-81177E Table IV)
- A-286 CRES (MS21140/41), min tensile preload: 5/32": 115 lb · 3/16": 169 lb · 1/4": 290 lb · 5/16": 417 lb (MIL-F-8975B Table III)
- Titanium (CR777x), min tensile preload: -04: 60 lb · -05: 180 lb · -06: 280 lb · -08: 420 lb · -10: 620 lb (Cherry PS-CMB-7000 Table IV)
Minimum installed-preload acceptance values from qualification testing (per MIL-STD/NASM-1312), roughly 10% of minimum tensile strength; not typical clamp-up.
What to check after install
- Stem position per diameter: alloy steel max protrusion -05: .020" to -10: .038", fracture surface may not recede below top of head; CRES/Ti protrusion and recession .010"-.020" by dash (CA-1039).
- Collar position: flush or below top of sleeve head, max values per dash.
- Head seating checked with a .002" feeler gage: a .002" gap is permissible over up to 40% of head circumference and must not reach the shank (CA-1039).
- Blind head minimum diameter per dash per the visual inspection tabulation.
Check gauges (2) and sources.Details
- 269B12 Maxibolt grip gage.
- .002" feeler gage for head seating.
Sources: CA-1039 process manual · MIL-F-81177E · MIL-F-8975B · PS-CMB-7000. Acceptance limits belong to the controlling spec; verify against your program's process documentation.
- Tool
- Cherry Maxibolt installation tooling and pulling heads (CA-1009 "Installation Tooling and Pulling Heads")
- Special / proprietary
- Special tooling · proprietary
- Training
- Not stated in the cited documents.
- Inspection
- Stem and collar position, head seating (.002" feeler) per CA-1039 (see verification below).
"-05 and -06 dia. fasteners are installed with a double action (shifting) tool; S05, S06, -08 and -10 dia. fasteners are installed with a single action (non-shifting) tool and are supplied with shift washer" (CA-1009 note 3). Titanium CR777x: "Titanium Maxibolt, shift washer type" (PS-CMB-7000).
The published install tool and nose for each size, other access options, and the gauges that check the install, from the manufacturer's own tool tables.
Full tool tables, envelopes, clearances and source notesCompare tooling burden across all 25 families
Cherry CA-1039 (MAXIBOLT process manual), Maxibolt Removal
- “Center punch, center drill.” Cherry CA-1039 (MAXIBOLT process manual), p.21, Maxibolt Removal ↗
- “It is recommended that a small center drill be used to provide a guide for a larger drill on top of the blind bolt stem, and the upper portion of the stem be drilled away to destroy the lock.” Cherry CA-1039 (MAXIBOLT process manual), p.21, Maxibolt Removal ↗
- “Drive out the stem using a punch pin.” Cherry CA-1039 (MAXIBOLT process manual), p.21, Maxibolt Removal ↗
- “Drill into blind bolt head avoiding contact with the top sheet material.” Cherry CA-1039 (MAXIBOLT process manual), p.21, Maxibolt Removal ↗
- “Break off the blind bolt head using a punch pin as a pry.” Cherry CA-1039 (MAXIBOLT process manual), p.21, Maxibolt Removal ↗
- “Drive out the remaining blind bolt shank with a punch pin having a diameter equal to the bolt shank.” Cherry CA-1039 (MAXIBOLT process manual), p.21, Maxibolt Removal ↗
Cautions
- “CAUTION: DO NOT drill completely through the head or the sleeve to remove a blind bolt as this will enlarge the hole.” Cherry CA-1039 (MAXIBOLT process manual), p.21, Maxibolt Removal ↗
None of the removal procedures on file gives a composite-specific removal caution. The Monogram specs address composite at the hole instead: holes "reasonably round and free from burrs (metallic structure) and delamination (graphite/epoxy type structure)" (MBF2003 §5.1).
P/N series CR7310 / CR7311 alloy steel (MS90353 / MS90354) · CR7620 / CR7621 A-286 (MS21140 / MS21141) · e.g. CR7310S-06-04 = MS90353S0604Paste a full part number into the decoder.
- Manufacturer
- Cherry
- Category
- Blind bolt
- Datasheet (PDF) ↗
- Manufacturer page ↗
- Cherry CA-1009 (Maxibolt catalog) + PS-CMB-7000 (titanium) ↗: CR7310/7311/7620/7621 tables: dimensions, grip limits, installed single shear & tensile (lbf), MS cross-reference. Titanium: PS-CMB-7000 §1.
- CA-1009 ↗ Cherry CA-1009
Find the part number for your stack
SpecLok has no dash-number table for this family yet: the quote line goes out as the family, part number to be confirmed.
Sourcing
Lead-time risk (SpecLok sourcing assessment): Medium
Get quotes: SpecLok sources this from authorized distributors and returns price, lead time and certs.You buy from the authorized distributor, who is named on your returned quote. SpecLok is free for buyers.
Supply signalfor this family
- 918 NSNs carry a part number of this family, recorded by 32 CAGE codes (FLIS, March 2025).
- Last DoD award for RIVET,BLIND items (FSC 5320): 2026-06-26; 3,082 awards since 2025-10-01.
- No SpecLok quotes yet.
A signal from records SpecLok holds, not availability, stock or a lead-time promise. FLIS lists who has recorded a part number for the item, not who makes it today. DoD awards carry no NSN or part number, so award activity is for the item name's class.
Sources: DLA FLIS Data Electronic Reading Room (PUB LOG) ↗, DLA PUB LOG ↗, USAspending.gov award search API ↗; DoD award data 2025-10-01 to 2026-07-06; compiled 2026-10-02.
Image credits: Cherry Aerospace, Cherry Maxibolt® Blind Bolt catalog CA-1009, p.1 ↗. Product images belong to their manufacturers.
Sources
- Cherry PS-CMB-7000 (Titanium MAXIBOLT)
- Cherry CA-1009 (Maxibolt catalog) + PS-CMB-7000 (titanium)
- Cherry product page
- Cherry CA-1039 (MAXIBOLT process manual)
- MIL-STD-889C Table I, graphite column: high = incompatible in marine atmosphere, sea water and industrial atmosphere; med = incompatible in marine atmosphere and sea water, compatible in industrial atmosphere (brass); low = compatible except sea water; unrated = not a Table I entry (non-metallic).
- MIL-F-81177E
- MIL-F-8975B
- Cherry CA-1015 (CherryMAX process manual)
- DLA FLIS Data Electronic Reading Room (PUB LOG)
- DLA PUB LOG
- USAspending.gov award search API
Next step
Free to ask. A person at SpecLok replies by email. You only pay the supplier if you accept a quote.
Spec a joint with the selector →Compare with other families →
Reference only: the controlling drawing, its process spec and the manufacturer's installation instructions govern. How to use these answers