← Tooling compatibility finder
H781A-456
H781A-456 Offset Pulling Head · Nose / pulling head · Cherry · Offset
H781A-456 installs CherryMAX® blind rivet -4, -5, -6 on a G704B, G747 or G800.
Traced from 2 manufacturer views, with published dimensions held fixed. Other shapes and unseen depths are inferred.
Built from 6 printed dimensions, 11 scaled from the figure.Details
Reference reconstruction traced from manufacturer views and constrained by printed dimensions. Undimensioned shapes and depths are inferred and labelled; omitted features mean this is not a guaranteed clearance boundary. NOT a manufacturing model or manufacturer CAD. Jaws and internal parts are not modelled. Verify fit and clearance against current manufacturer data and the physical tool.
- 3.5 The frame's front face to its back end · Cherry TS-H781A-456 instruction sheet (Rev D, 29 Dec 16), p.1, Fig. 1
- 7/8 The nose stub's front to the top guard's back end · Cherry TS-H781A-456 instruction sheet (Rev D, 29 Dec 16), p.1, Fig. 1
- 3/16 The nose stub's projection in front of the frame · Cherry TS-H781A-456 instruction sheet (Rev D, 29 Dec 16), p.1, Fig. 1
- 3/16 Fastener centreline to the top of the head · Cherry TS-H781A-456 instruction sheet (Rev D, 29 Dec 16), p.1, Fig. 1
- 1.000 Fastener centreline to the tool centreline · Cherry TS-H781A-456 instruction sheet (Rev D, 29 Dec 16), p.1, Fig. 1
- .59 The head's width at the fastener centreline (end view) · Cherry TS-H781A-456 instruction sheet (Rev D, 29 Dec 16), p.1, Fig. 1
Scaled from the catalog figure, not dimensioned
- Frame: side outline (length): 3.50 in (scaled from Cherry TS-H781A-456 instruction sheet (Rev D, 29 Dec 16) p.1, Fig. 1 (Rev D), side view, not dimensioned)
- Frame: end view outline (widest): 1.02 in (scaled from Cherry TS-H781A-456 instruction sheet (Rev D, 29 Dec 16) p.1, Fig. 1 (Rev D), end view, not dimensioned)
- Frame: top view outline (widest): 1.02 in (scaled from Cherry TS-H781A-456 instruction sheet (Rev D, 29 Dec 16) p.1, top view, not dimensioned)
- Frame: slot through the side (height): 0.20 in (scaled from Cherry TS-H781A-456 instruction sheet (Rev D, 29 Dec 16) p.1, Fig. 1 (Rev D), side view, not dimensioned)
- Drawbar pin: diameter: 0.16 in (scaled from Cherry TS-H781A-456 instruction sheet (Rev D, 29 Dec 16) p.1, Fig. 1 (Rev D), side view, not dimensioned)
- Nose stub: largest diameter: 0.38 in (scaled from Cherry TS-H781A-456 instruction sheet (Rev D, 29 Dec 16) p.1, Fig. 1 (Rev D), side view, not dimensioned)
- Nose stub: bore diameter: 0.16 in (scaled from Cherry TS-H781A-456 instruction sheet (Rev D, 29 Dec 16) p.1, Fig. 1 (Rev D), side view, not dimensioned)
- Mount neck: largest diameter: 0.68 in (scaled from Cherry TS-H781A-456 instruction sheet (Rev D, 29 Dec 16) p.1, Fig. 1 (Rev D), side view, not dimensioned)
- Mount thread front: crest spacing (as drawn; not a thread specification): 0.05 in (scaled from Cherry TS-H781A-456 instruction sheet (Rev D, 29 Dec 16) p.1, Fig. 1 (Rev D), side view, not dimensioned)
- Jam nut: across flats: 0.88 in (scaled from Cherry TS-H781A-456 instruction sheet (Rev D, 29 Dec 16) p.1, Fig. 1 (Rev D), side view, not dimensioned)
- Mount thread rear: crest spacing (as drawn; not a thread specification): 0.05 in (scaled from Cherry TS-H781A-456 instruction sheet (Rev D, 29 Dec 16) p.1, Fig. 1 (Rev D), side view, not dimensioned)
- Built from the tool sheet's Fig. 1 (end, side and top views): the frame is sliced along its length, each slice the end view's outline cut to the side view's height and the top view's width there.
- Fastener axis to the left (-x), 1.000 above the tool axis (y = 0); x = 0 at the frame's front face.
- The end view's R1/2 and .17 and the .78 slot length are printed but not used to size the model: the end view's outline and the slot are scaled from the figure (R1/2 agrees with the outline drawn: 56.5 px at the end view's 111 px per inch is 0.51).
Not modelled
Everything it installs1 fastener group
CherryMAX® blind rivet (NAS9301 to NAS9312 / CR3213 to CR3555P) -4, -5, -6, per the Cherry catalog
Fastener process documents that name it1
- CherryMAX -4, -5, -6 Cherry CA-1015 p.20 ↗
Other brands' equivalents0 statements
No cross-brand statement on file for these tools. Not documented is not the same as incompatible.
Sources5
- Cherry Fastening Systems for Aerospace Tool Catalog (©2015 edition, archived), p.26, CherryMAX® Blind Rivets & Tools, Cherry Power Tools ↗
- Inconel part: "NOTE: G704B/G83A/G84 power riveters recommended for installation of Inconel fasteners due to high break stem loads" (©2015 guide p.26). The G747 and G800 the same table lists are left off for Inconel.
- "*** Use adapter 680B205" (p.26). -4 and -5 only: CA-1015 p.5 does not shade -6 for the G784 with CherryMAX® heads, though p.26 and CA-1001 p.13 print -6; confirm with Cherry before using it at -6.
- Cherry CA-1001 Tool Catalog (2017), p.6, Pulling Heads table ↗
- Nominal diameters. Section 1 riveter with a Section 1 pulling head (CA-1001 p.1, p.6); CA-1015 p.5 shades nominal -4, -5, -6. The ©2015 CherryMAX guide (p.26) does not list the G746A.
- Cherry CA-1015 (CherryMAX process manual), p.5, CherryMAX® Tool Selection (shaded chart) ↗
- Oversize diameters: CA-1015 p.5 shades the G746A for oversize -4 and -5 only (not -6).
- Cherry CA-1001 Tool Catalog (2017), p.22, Riveter Adapters ↗
- 744-300: G83A, G84 to the G704B (CherryMAX®) mounting system "for H701B, H747, H781A, H782, H753A"; "Must remove the bayonet adapter".
- Cherry CA-1015 (CherryMAX process manual), p.20, Pulling Heads ↗
- Drawn with the H781-456 on CA-1015 p.20 (same figure and dimensions).
Tool catalogs are the manufacturers' as published in the cited edition; confirm current PNs with the tool maker before purchase. Install per the OEM process specification.
Published dimensions13 · for envelope CAD
| Feature | Value | As printed | Source |
|---|---|---|---|
| Overall length | 3.390625 in | 3-25/64" | Cherry CA-1001 Tool Catalog (2017), p.6, H781A-456 drawing ↗ |
| As drawn (feature not labeled) | 0.875 in | 7/8" | Cherry CA-1001 Tool Catalog (2017), p.6, H781A-456 drawing ↗ |
| As drawn (feature not labeled) | 0.1875 in | 3/16" Drawn on a photo near the jaw; the catalog does not label what it spans, so it is not used for a clearance verdict. A second 3/16" is drawn at the jaw. | Cherry CA-1001 Tool Catalog (2017), p.6, H781A-456 drawing ↗ |
| As drawn (feature not labeled) | 1 in | 1" | Cherry CA-1001 Tool Catalog (2017), p.6, H781A-456 drawing ↗ |
| As drawn (feature not labeled) | 3.5 in | 3.5 Side view: the frame's front face to its back end (where the mounting thread starts). | Cherry TS-H781A-456 instruction sheet (Rev D, 29 Dec 16), p.1, Fig. 1 ↗ |
| As drawn (feature not labeled) | 0.875 in | 7/8 Side view: the front of the nose stub to the back end of the top guard. | Cherry TS-H781A-456 instruction sheet (Rev D, 29 Dec 16), p.1, Fig. 1 ↗ |
| As drawn (feature not labeled) | 0.1875 in | 3/16 Side view, along the fastener axis: the nose stub's projection in front of the frame. | Cherry TS-H781A-456 instruction sheet (Rev D, 29 Dec 16), p.1, Fig. 1 ↗ |
| As drawn (feature not labeled) | 0.1875 in | 3/16 Side view: the fastener centreline to the top of the head (vertical). | Cherry TS-H781A-456 instruction sheet (Rev D, 29 Dec 16), p.1, Fig. 1 ↗ |
| Offset head height | 1 in | 1.000 Side view: the fastener centreline to the tool centreline (the offset). | Cherry TS-H781A-456 instruction sheet (Rev D, 29 Dec 16), p.1, Fig. 1 ↗ |
| As drawn (feature not labeled) | 0.78 in | .78 Side view: the drawbar slot, centre to centre of its ends. | Cherry TS-H781A-456 instruction sheet (Rev D, 29 Dec 16), p.1, Fig. 1 ↗ |
| Head width | 0.59 in | .59 End view: the head's width at the fastener centreline (the top lobe). | Cherry TS-H781A-456 instruction sheet (Rev D, 29 Dec 16), p.1, Fig. 1 ↗ |
| As drawn (feature not labeled) | 0.5 in | R1/2 End view: radius of the frame's rounded bottom. | Cherry TS-H781A-456 instruction sheet (Rev D, 29 Dec 16), p.1, Fig. 1 ↗ |
| As drawn (feature not labeled) | 0.17 in | .17 End view: the inner channel's floor to the bottom of the frame. | Cherry TS-H781A-456 instruction sheet (Rev D, 29 Dec 16), p.1, Fig. 1 ↗ |
Only dimensions a document prints are listed, with the feature each one measures. A length read from a part number by a rule the cited chart prints is marked "Not printed as a number". None of these catalogs publishes nose tip or anvil geometry detailed enough to machine from.
On the floor:Low clearance puller finderLow profile CherryMAX puller: printed head heights
Reference only: the controlling drawing, its process spec and the manufacturer's installation instructions govern. How to use these answers
Next step
Free to ask. A person at SpecLok replies by email. You only pay the supplier if you accept a quote.