← Tooling compatibility finder
H782
H782 Offset Pulling Head · Nose / pulling head · Cherry · Offset
H782 installs CherryMAX® blind rivet -4, -5, -6 on a G704B, G747 or G800.
Traced from 2 manufacturer views, with published dimensions held fixed. Other shapes and unseen depths are inferred.
Built from 8 printed dimensions, 13 scaled from the figure.Details
Reference reconstruction traced from manufacturer views and constrained by printed dimensions. Undimensioned shapes and depths are inferred and labelled; omitted features mean this is not a guaranteed clearance boundary. NOT a manufacturing model or manufacturer CAD. Jaws and internal parts are not modelled. Verify fit and clearance against current manufacturer data and the physical tool.
- 4.59 The front to the back face of the adapter's hex · Cherry TS-H782 instruction sheet (Rev H, 26 Mar 15), p.1, Fig. 1 Dimensional Data
- 3.67 The front to the frame's back end · Cherry TS-H782 instruction sheet (Rev H, 26 Mar 15), p.1, Fig. 1 Dimensional Data
- 1.53 The front to the step on the carrier's top · Cherry TS-H782 instruction sheet (Rev H, 26 Mar 15), p.1, Fig. 1 Dimensional Data
- 1.09 The carrier's top step to the deflector's top end · Cherry TS-H782 instruction sheet (Rev H, 26 Mar 15), p.1, Fig. 1 Dimensional Data
- 1.72 The front to the step on the frame's bottom · Cherry TS-H782 instruction sheet (Rev H, 26 Mar 15), p.1, Fig. 1 Dimensional Data
- .250 Fastener centreline to the top of the head · Cherry TS-H782 instruction sheet (Rev H, 26 Mar 15), p.1, Fig. 1 Dimensional Data
- 1.00 Offset Distance Fastener centreline to the tool centreline · Cherry TS-H782 instruction sheet (Rev H, 26 Mar 15), p.1, Fig. 1 Dimensional Data
- .56 Width of the frame's bottom face (end view) · Cherry TS-H782 instruction sheet (Rev H, 26 Mar 15), p.1, Fig. 1 Dimensional Data
Scaled from the catalog figure, not dimensioned
- Frame and carrier: side outline (length): 3.67 in (scaled from Cherry TS-H782 instruction sheet (Rev H, 26 Mar 15) p.1, Fig. 1 Dimensional Data, side view, not dimensioned)
- Frame and carrier: end view outline (widest): 1.11 in (scaled from Cherry TS-H782 instruction sheet (Rev H, 26 Mar 15) p.1, Fig. 1 Dimensional Data, end view, not dimensioned)
- Frame and carrier: slot through the side (height): 0.19 in (scaled from Cherry TS-H782 instruction sheet (Rev H, 26 Mar 15) p.1, Fig. 1 Dimensional Data, side view, not dimensioned)
- Drawbar pin: diameter: 0.16 in (scaled from Cherry TS-H782 instruction sheet (Rev H, 26 Mar 15) p.1, Fig. 1 Dimensional Data, side view, not dimensioned)
- Nosepiece: largest diameter: 0.45 in (scaled from Cherry TS-H782 instruction sheet (Rev H, 26 Mar 15) p.1, Fig. 1 Dimensional Data, side view, not dimensioned)
- Mount neck: largest diameter: 0.80 in (scaled from Cherry TS-H782 instruction sheet (Rev H, 26 Mar 15) p.1, Fig. 1 Dimensional Data, side view, not dimensioned)
- Adaptor thread: crest spacing (as drawn; not a thread specification): 0.05 in (scaled from Cherry TS-H782 instruction sheet (Rev H, 26 Mar 15) p.1, Fig. 1 Dimensional Data, side view, not dimensioned)
- Adaptor hex: across flats: 1.01 in (scaled from Cherry TS-H782 instruction sheet (Rev H, 26 Mar 15) p.1, Fig. 1 Dimensional Data, side view, not dimensioned)
- Adaptor neck: largest diameter: 0.73 in (scaled from Cherry TS-H782 instruction sheet (Rev H, 26 Mar 15) p.1, Fig. 1 Dimensional Data, side view, not dimensioned)
- Mount thread front: crest spacing (as drawn; not a thread specification): 0.05 in (scaled from Cherry TS-H782 instruction sheet (Rev H, 26 Mar 15) p.1, Fig. 1 Dimensional Data, side view, not dimensioned)
- Jam nut: across flats: 0.88 in (scaled from Cherry TS-H782 instruction sheet (Rev H, 26 Mar 15) p.1, Fig. 1 Dimensional Data, side view, not dimensioned)
- Mount thread rear: crest spacing (as drawn; not a thread specification): 0.05 in (scaled from Cherry TS-H782 instruction sheet (Rev H, 26 Mar 15) p.1, Fig. 1 Dimensional Data, side view, not dimensioned)
- Mount end: largest diameter: 0.65 in (scaled from Cherry TS-H782 instruction sheet (Rev H, 26 Mar 15) p.1, Fig. 1 Dimensional Data, side view, not dimensioned)
- Built from the tool sheet's Fig. 1 (end and side views): the frame and carrier are sliced along their length, each slice the end view's outline cut to the side view's height there; where the carrier stands clear of the frame the two are separate pieces.
- Fastener axis to the left (-x), 1.00 above the tool axis (y = 0); x = 0 at the front (the dimensions' common extension line).
- The catalog photo's 4-19/32, 3-11/16, 1-3/32, 1-17/32, 1-19/32 and 1-23/32 are kept on the tool's page but not used here.
Not modelled
Everything it installs1 fastener group
CherryMAX® blind rivet (NAS9301 to NAS9312 / CR3213 to CR3555P) -4, -5, -6, per the Cherry catalog
Fastener process documents that name it3
- CherryMAX -4, -5, -6 Cherry CA-1015 p.20 ↗
- Cherry Maxibolt -4, -5 Cherry CA-1015 p.20 ↗
- Cherry SST -4, -5, -6 Cherry CA-1015 p.20 ↗
Other brands' equivalents1 statement
- Gage Bilt says 456MAX-704-40OS replaces H782 (Cherry) Gage Bilt 2017 p.156 ↗
Gage Bilt's cross-reference lists 456MAX-704-40OS (nose assembly - offset) for H782.
Sources6
- Cherry Fastening Systems for Aerospace Tool Catalog (©2015 edition, archived), p.26, CherryMAX® Blind Rivets & Tools, Cherry Power Tools ↗
- Inconel part: "NOTE: G704B/G83A/G84 power riveters recommended for installation of Inconel fasteners due to high break stem loads" (©2015 guide p.26). The G747 and G800 the same table lists are left off for Inconel.
- "*** Use adapter 680B205" (p.26). -4 and -5 only: CA-1015 p.5 does not shade -6 for the G784 with CherryMAX® heads, though p.26 and CA-1001 p.13 print -6; confirm with Cherry before using it at -6.
- Cherry CA-1001 Tool Catalog (2017), p.6, Pulling Heads table ↗
- Nominal diameters. Section 1 riveter with a Section 1 pulling head (CA-1001 p.1, p.6); CA-1015 p.5 shades nominal -4, -5, -6. The ©2015 CherryMAX guide (p.26) does not list the G746A.
- Cherry CA-1015 (CherryMAX process manual), p.5, CherryMAX® Tool Selection (shaded chart) ↗
- Oversize diameters: CA-1015 p.5 shades the G746A for oversize -4 and -5 only (not -6).
- Cherry CA-1001 Tool Catalog (2017), p.22, Riveter Adapters ↗
- 744-300: G83A, G84 to the G704B (CherryMAX®) mounting system "for H701B, H747, H781A, H782, H753A"; "Must remove the bayonet adapter".
- Cherry CA-1015 (CherryMAX process manual), p.20, Pulling Heads ↗
- Gage Bilt Aerospace Catalog 2017 (archived; pages are PDF pages), p.156, Other - Gage Bilt Cross Reference, page 51 ↗
Tool catalogs are the manufacturers' as published in the cited edition; confirm current PNs with the tool maker before purchase. Install per the OEM process specification.
Published dimensions18 · for envelope CAD
| Feature | Value | As printed | Source |
|---|---|---|---|
| Overall length | 4.59375 in | 4-19/32" | Cherry CA-1001 Tool Catalog (2017), p.6, H782 drawing ↗ |
| As drawn (feature not labeled) | 3.6875 in | 3-11/16" | Cherry CA-1001 Tool Catalog (2017), p.6, H782 drawing ↗ |
| As drawn (feature not labeled) | 1.09375 in | 1-3/32" | Cherry CA-1001 Tool Catalog (2017), p.6, H782 drawing ↗ |
| As drawn (feature not labeled) | 1.53125 in | 1-17/32" | Cherry CA-1001 Tool Catalog (2017), p.6, H782 drawing ↗ |
| As drawn (feature not labeled) | 1.59375 in | 1-19/32" | Cherry CA-1001 Tool Catalog (2017), p.6, H782 drawing ↗ |
| As drawn (feature not labeled) | 1.71875 in | 1-23/32" | Cherry CA-1001 Tool Catalog (2017), p.6, H782 drawing ↗ |
| As drawn (feature not labeled) | 4.59 in | 4.59 Side view: the frame's front face to the back face of the adapter's hex. | Cherry TS-H782 instruction sheet (Rev H, 26 Mar 15), p.1, Fig. 1 Dimensional Data ↗ |
| As drawn (feature not labeled) | 3.67 in | 3.67 Side view: the frame's front face to its back end. | Cherry TS-H782 instruction sheet (Rev H, 26 Mar 15), p.1, Fig. 1 Dimensional Data ↗ |
| As drawn (feature not labeled) | 1.53 in | 1.53 Side view: the frame's front face to the step on the carrier's top. | Cherry TS-H782 instruction sheet (Rev H, 26 Mar 15), p.1, Fig. 1 Dimensional Data ↗ |
| As drawn (feature not labeled) | 1.09 in | 1.09 Side view: the carrier's top step to the deflector's top end. | Cherry TS-H782 instruction sheet (Rev H, 26 Mar 15), p.1, Fig. 1 Dimensional Data ↗ |
| As drawn (feature not labeled) | 1.72 in | 1.72 Side view: the frame's front face to the step on its bottom edge. | Cherry TS-H782 instruction sheet (Rev H, 26 Mar 15), p.1, Fig. 1 Dimensional Data ↗ |
| As drawn (feature not labeled) | 0.25 in | .250 End view: the fastener centreline to the top of the head. | Cherry TS-H782 instruction sheet (Rev H, 26 Mar 15), p.1, Fig. 1 Dimensional Data ↗ |
| Offset head height | 1 in | 1.00 Offset Distance End view: the fastener centreline to the tool centreline. | Cherry TS-H782 instruction sheet (Rev H, 26 Mar 15), p.1, Fig. 1 Dimensional Data ↗ |
| As drawn (feature not labeled) | 0.56 in | .56 End view: the width of the frame's bottom face. | Cherry TS-H782 instruction sheet (Rev H, 26 Mar 15), p.1, Fig. 1 Dimensional Data ↗ |
As printed in the fastener process documents
- Overall length (as dimensioned): 4 5/8" (117,48 mm) (CherryMAX, Cherry Maxibolt, Cherry SST, Cherry CA-1015 (CherryMAX process manual), p.20, Pulling Heads ↗)
- Second length (as dimensioned): 3 5/8" (92,08 mm) (CherryMAX, Cherry Maxibolt, Cherry SST, Cherry CA-1015 (CherryMAX process manual), p.20, Pulling Heads ↗)
- Height (as dimensioned): 1-3/4" (44,5 mm) (CherryMAX, Cherry Maxibolt, Cherry SST, Cherry CA-1015 (CherryMAX process manual), p.20, Pulling Heads ↗)
- Other dimensions shown: 1 9/16" (39,69 mm); 1 1/8" (28,58 mm) (CherryMAX, Cherry Maxibolt, Cherry SST, Cherry CA-1015 (CherryMAX process manual), p.20, Pulling Heads ↗)
Only dimensions a document prints are listed, with the feature each one measures. A length read from a part number by a rule the cited chart prints is marked "Not printed as a number". None of these catalogs publishes nose tip or anvil geometry detailed enough to machine from.
On the floor:Low clearance puller finderLow profile CherryMAX puller: printed head heights
Reference only: the controlling drawing, its process spec and the manufacturer's installation instructions govern. How to use these answers
Next step
Free to ask. A person at SpecLok replies by email. You only pay the supplier if you accept a quote.