← Tooling compatibility finder

H747-456

H747-456 Straight Pulling Head · Nose / pulling head · Cherry · Standard

Loading 3D view...
Traced reference model. Not for machining or verified fit.

Traced from 1 manufacturer view, with published dimensions held fixed. Other shapes and unseen depths are inferred.

Built from 4 printed dimensions, 17 scaled from the figure.Details

Reference reconstruction traced from manufacturer views and constrained by printed dimensions. Undimensioned shapes and depths are inferred and labelled; omitted features mean this is not a guaranteed clearance boundary. NOT a manufacturing model or manufacturer CAD. Jaws and internal parts are not modelled. Verify fit and clearance against current manufacturer data and the physical tool.

Scaled from the catalog figure, not dimensioned

  • Rear thread: diameter: 0.75 in (scaled from Cherry TS-H747-456 instruction sheet (Rev D, 26 Mar 15) p.1, Fig. 1 Dimensional Data (Rev D), not dimensioned)
  • Jam nut: hex across flats: 0.89 in (scaled from Cherry TS-H747-456 instruction sheet (Rev D, 26 Mar 15) p.1, Fig. 1 Dimensional Data (Rev D), not dimensioned)
  • Front thread: diameter: 0.75 in (scaled from Cherry TS-H747-456 instruction sheet (Rev D, 26 Mar 15) p.1, Fig. 1 Dimensional Data (Rev D), not dimensioned)
  • Sleeve shoulder: outline: 0.75 in (scaled from Cherry TS-H747-456 instruction sheet (Rev D, 26 Mar 15) p.1, Fig. 1 Dimensional Data (Rev D), not dimensioned)
  • Hex sleeve: length: 1.52 in (scaled from Cherry TS-H747-456 instruction sheet (Rev D, 26 Mar 15) p.1, Fig. 1 Dimensional Data (Rev D), not dimensioned)
  • Sleeve nose: outline: 0.63 in (scaled from Cherry TS-H747-456 instruction sheet (Rev D, 26 Mar 15) p.1, Fig. 1 Dimensional Data (Rev D), not dimensioned)
  • Nosepiece: outline: 0.45 in (scaled from Cherry TS-H747-456 instruction sheet (Rev D, 26 Mar 15) p.1, Fig. 1 Dimensional Data (Rev D), not dimensioned)
  • Compression spring: outside diameter: 0.18 in (scaled from Cherry TS-H747-456 instruction sheet (Rev D, 26 Mar 15) p.1, Fig. 1 Dimensional Data (Rev D), not dimensioned)
  • Sleeve thread rear: crest spacing (as drawn; not a thread specification): 0.05 in (scaled from Cherry TS-H747-456 instruction sheet (Rev D, 26 Mar 15) p.1, Fig. 1 Dimensional Data (Rev D), not dimensioned)
  • Jam nut: across flats: 0.89 in (scaled from Cherry TS-H747-456 instruction sheet (Rev D, 26 Mar 15) p.1, Fig. 1 Dimensional Data (Rev D), not dimensioned)
  • Sleeve thread front: crest spacing (as drawn; not a thread specification): 0.05 in (scaled from Cherry TS-H747-456 instruction sheet (Rev D, 26 Mar 15) p.1, Fig. 1 Dimensional Data (Rev D), not dimensioned)
  • Sleeve shoulder: outline (largest diameter): 0.75 in (scaled from Cherry TS-H747-456 instruction sheet (Rev D, 26 Mar 15) p.1, Fig. 1 Dimensional Data (Rev D), not dimensioned)
  • Hex sleeve: across flats: 0.56 in (scaled from Cherry TS-H747-456 instruction sheet (Rev D, 26 Mar 15) p.1, Fig. 1 Dimensional Data (Rev D), not dimensioned)
  • Sleeve nose chamfer: across flats: 0.56 in (scaled from Cherry TS-H747-456 instruction sheet (Rev D, 26 Mar 15) p.1, Fig. 1 Dimensional Data (Rev D), not dimensioned)
  • Sleeve nose: outline (largest diameter): 0.56 in (scaled from Cherry TS-H747-456 instruction sheet (Rev D, 26 Mar 15) p.1, Fig. 1 Dimensional Data (Rev D), not dimensioned)
  • Nosepiece: across flats: 0.40 in (scaled from Cherry TS-H747-456 instruction sheet (Rev D, 26 Mar 15) p.1, Fig. 1 Dimensional Data (Rev D), not dimensioned)
  • Nosepiece: bore diameter: 0.13 in (scaled from Cherry TS-H747-456 instruction sheet (Rev D, 26 Mar 15) p.1, Fig. 1 Dimensional Data (Rev D), not dimensioned)

Not modelled

    Everything it installs1 fastener group

    CherryMAX® blind rivet (NAS9301 to NAS9312 / CR3213 to CR3555P) -4, -5, -6, per the Cherry catalog

    Fastener process documents that name it2
    Other brands' equivalents1 statement
    Sources7
    1. Cherry Fastening Systems for Aerospace Tool Catalog (©2015 edition, archived), p.26, CherryMAX® Blind Rivets & Tools, Cherry Power Tools ↗
      • Inconel part: "NOTE: G704B/G83A/G84 power riveters recommended for installation of Inconel fasteners due to high break stem loads" (©2015 guide p.26). The G747 and G800 the same table lists are left off for Inconel.
    2. Cherry CA-1001 Tool Catalog (2017), p.6, Pulling Heads table ↗
      • Nominal diameters. Section 1 riveter with a Section 1 pulling head (CA-1001 p.1, p.6); CA-1015 p.5 shades nominal -4, -5, -6. The ©2015 CherryMAX guide (p.26) does not list the G746A.
    3. Cherry CA-1015 (CherryMAX process manual), p.5, CherryMAX® Tool Selection (shaded chart) ↗
      • Oversize diameters: CA-1015 p.5 shades the G746A for oversize -4 and -5 only (not -6).
    4. Cherry CA-1001 Tool Catalog (2017), p.22, Riveter Adapters ↗
      • 744-300: G83A, G84 to the G704B (CherryMAX®) mounting system "for H701B, H747, H781A, H782, H753A"; "Must remove the bayonet adapter".
    5. Cherry CA-1015 (CherryMAX process manual), p.20, Pulling Heads ↗
    6. Cherry CA-1035 (Cherry 1900), p.2, Tooling ↗
    7. Gage Bilt Aerospace Catalog 2017 (archived; pages are PDF pages), p.156, Other - Gage Bilt Cross Reference, page 51 ↗

    Tool catalogs are the manufacturers' as published in the cited edition; confirm current PNs with the tool maker before purchase. Install per the OEM process specification.

    Published dimensions7 · for envelope CAD
    FeatureValueAs printedSource
    Overall length2.34375 in2-11/32"Cherry CA-1001 Tool Catalog (2017), p.6, H747-456 drawing ↗
    Length from tool face1.65625 in1-21/32"

    Drawn from the mounting flange to the tip.

    Cherry CA-1001 Tool Catalog (2017), p.6, H747-456 drawing ↗
    Nose diameter0.625 in5/8"

    Across the hex sleeve's corners (the tool sheet's side view shows a flat face-on).

    Cherry CA-1001 Tool Catalog (2017), p.6, H747-456 drawing ↗
    Centerline to edge0.28 in.28 EDGE DISTANCE AT FLATS

    End view: centreline to the hex sleeve's flats. Across the corners the sleeve is wider.

    Cherry TS-H747-456 instruction sheet (Rev D, 26 Mar 15), p.1, Fig. 1 Dimensional Data ↗

    As printed in the fastener process documents

    Only dimensions a document prints are listed, with the feature each one measures. A length read from a part number by a rule the cited chart prints is marked "Not printed as a number". None of these catalogs publishes nose tip or anvil geometry detailed enough to machine from.

    On the floor:Low clearance puller finderLow profile CherryMAX puller: printed head heights

    Reference only: the controlling drawing, its process spec and the manufacturer's installation instructions govern. How to use these answers

    Next step

    Free to ask. A person at SpecLok replies by email. You only pay the supplier if you accept a quote.

    Find tooling for a part number →Tooling shop →