Low clearance puller finder
Enter the space you have, in inches. Each answer compares it with one dimension printed in the Cherry, Huck or Gage Bilt tool catalog. It is not a fit check of the whole tool.
CR3213, 2.25 in headroom
No margin: 1 · Dimension not published: 4 · Does not fit: 10
"Printed dimension fits" means the one catalog dimension named is smaller than the clearance you entered. It covers that edge of the nose or head only. It does not cover the riveter the nose mounts on, the rest of the nose, the fastener's stem, stroke, hoses, your hand or anything the catalog does not dimension. The tool has to be tried in place before the job.
The aircraft's structural repair manual and the manufacturer's installation instructions govern. The tool manufacturer's data sheet governs the tool's dimensions.
Reference only: the controlling drawing, its process spec and the manufacturer's installation instructions govern. How to use these answers
Cherry tooling, for Cherry-made parts
10Right angle
- Headroom Head height (nose tip to back of head) 2.25 in (printed 2-1/4"). Equal to your clearance, no margin.
- Head height, nose tip to back of head
- 2.25 in (printed 2-1/4") Cherry CA-1001 Tool Catalog p.6
- Fastener centreline to one edge of the nose
- dimension not published
On G704B, G704B-SR, G704B-40SH, G747, G800, G746A. On G83A, G84 with adapter 744-300. On G784 with adapter 680B205. Cherry tool catalog 2015 p.26
Request this tool: buy, rent or repair →- Headroom Head height: dimension not published.
- Head height, nose tip to back of head
- dimension not published
- Fastener centreline to one edge of the nose
- dimension not published
On G84 with adapter 744-200. Cherry tool catalog 2015 p.26
Request this tool: buy, rent or repair →- Headroom Head height: dimension not published.
- Head height, nose tip to back of head
- dimension not published
- Fastener centreline to one edge of the nose
- dimension not published
On G84. Cherry CA-1001 Tool Catalog p.8
Request this tool: buy, rent or repair →
OffsetThe nose mounts in line with the riveter. No document on file prints the riveter's length behind it.
- Headroom Nose length: dimension not published. The nose mounts in line with the riveter. No document on file prints the riveter's length behind it.
- Nose length, in line with the riveter
- dimension not published
- Fastener centreline to one edge of the nose
- dimension not published
On G84 with adapter 744-200. Cherry tool catalog 2015 p.26
Request this tool: buy, rent or repair →- Headroom The nose alone is 3.3906 in (printed 3-25/64"), before the riveter behind it.
- Nose length, in line with the riveter
- 3.3906 in (printed 3-25/64") Cherry CA-1001 Tool Catalog p.6
- Fastener centreline to one edge of the nose
- dimension not published
On G704B, G704B-SR, G704B-40SH, G747, G800, G746A. On G83A, G84 with adapter 744-300. On G784 with adapter 680B205. Cherry tool catalog 2015 p.26
Request this tool: buy, rent or repair →- Headroom The nose alone is 4.5938 in (printed 4-19/32"), before the riveter behind it.
- Nose length, in line with the riveter
- 4.5938 in (printed 4-19/32") Cherry CA-1001 Tool Catalog p.6
- Fastener centreline to one edge of the nose
- dimension not published
On G704B, G704B-SR, G704B-40SH, G747, G800, G746A. On G83A, G84 with adapter 744-300. On G784 with adapter 680B205. Cherry tool catalog 2015 p.26
Request this tool: buy, rent or repair →
StandardThe nose mounts in line with the riveter. No document on file prints the riveter's length behind it.
- Headroom Nose length: dimension not published. The nose mounts in line with the riveter. No document on file prints the riveter's length behind it.
- Nose length, in line with the riveter
- dimension not published
- Fastener centreline to one edge of the nose
- dimension not published
On G784. Cherry tool catalog 2015 p.26
Request this tool: buy, rent or repair →- Headroom The nose alone is 2.25 in (printed 2-1/4), before the riveter behind it.
- Nose length, in line with the riveter
- 2.25 in (printed 2-1/4) Cherry TS-H701B-456 instruction sheet p.1
- Fastener centreline to one edge of the nose
- 0.21 in (printed .21) Cherry TS-H701B-456 instruction sheet p.1End view: centreline to the flat on the nose. The side view draws the flat at the tip only and prints no length for it; behind it the nose is 3/4 in. diameter.
On G704B, G704B-SR, G704B-40SH, G747, G800, G746A. On G83A, G84 with adapter 744-300. Cherry tool catalog 2015 p.26
Request this tool: buy, rent or repair →- Headroom The nose alone is 2.3438 in (printed 2-11/32"), before the riveter behind it.
- Nose length, in line with the riveter
- 2.3438 in (printed 2-11/32") Cherry CA-1001 Tool Catalog p.6
- Fastener centreline to one edge of the nose
- 0.28 in (printed .28 EDGE DISTANCE AT FLATS) Cherry TS-H747-456 instruction sheet p.1End view: centreline to the hex sleeve's flats. Across the corners the sleeve is wider.
On G704B, G704B-SR, G704B-40SH, G747, G800, G746A. On G83A, G84 with adapter 744-300. Cherry tool catalog 2015 p.26
Request this tool: buy, rent or repair →- Headroom The nose alone is 2.83 in (printed 2.83"), before the riveter behind it.
- Nose length, in line with the riveter
- 2.83 in (printed 2.83") Cherry CA-1001 Tool Catalog p.8
- Fastener centreline to one edge of the nose
- dimension not published
On G84. Cherry CA-1015 p.5
Request this tool: buy, rent or repair →
Gage Bilt tooling. Gage Bilt's chart names Cherry, Allfast, Huck rivets
5Right angle
- Headroom Head height (nose tip to back of head) 3.48 in (printed 3.48 (88.4 mm)). 1.23 in over.
- Head height, nose tip to back of head
- 3.48 in (printed 3.48 (88.4 mm)) Gage Bilt catalog 2017 p.43
- Fastener centreline to one edge of the nose
- dimension not published
On GB704. Gage Bilt catalog 2017 p.43
Request this tool: buy, rent or repair →
OffsetThe nose mounts in line with the riveter. No document on file prints the riveter's length behind it.
- Headroom The nose alone is 4.312 in (printed 4.312), before the riveter behind it.
- Nose length, in line with the riveter
- 4.312 in (printed 4.312) Gage Bilt catalog 2017 p.43
- Fastener centreline to one edge of the nose
- dimension not published
On GB704. Gage Bilt catalog 2017 p.43
Request this tool: buy, rent or repair →
StandardThe nose mounts in line with the riveter. No document on file prints the riveter's length behind it.
- Headroom The nose alone is 2.25 in (printed 2.25), before the riveter behind it.
- Nose length, in line with the riveter
- 2.25 in (printed 2.25) Gage Bilt catalog 2017 p.43
- Fastener centreline to one edge of the nose
- dimension not published
On GB704. Gage Bilt catalog 2017 p.43
Request this tool: buy, rent or repair →- Headroom The nose alone is 3.5 in (not a printed number: read from the part number by the chart's note), before the riveter behind it.
- Nose length, in line with the riveter
- 3.5 in (not a printed number: read from the part number by the chart's note) Gage Bilt catalog 2017 p.41
- Fastener centreline to one edge of the nose
- dimension not published
On GB704. Gage Bilt catalog 2017 p.41
Request this tool: buy, rent or repair →- Headroom The nose alone is 3.5 in (not a printed number: read from the part number by the chart's note), before the riveter behind it.
- Nose length, in line with the riveter
- 3.5 in (not a printed number: read from the part number by the chart's note) Gage Bilt catalog 2017 p.41
- Fastener centreline to one edge of the nose
- dimension not published
On GB704. Gage Bilt catalog 2017 p.41
Request this tool: buy, rent or repair →
How the answer is worked outrules
- Right angle head: the catalog's head height, nose tip to back of head, is compared with your headroom. Where the catalog figure draws the tool body rising above that height with no dimension, the answer is "dimension not published".
- Straight or offset nose: it mounts in line with the riveter, and no catalog on file prints the riveter's length behind it. If the nose alone is as long as your headroom it does not fit. Otherwise the answer is "dimension not published".
- Side clearance: the catalog's centreline to edge dimension is compared with your distance to one wall. Most of these are drawn to one edge only, a flat or the offset edge of the head, and the note with each value says which. A nose diameter is never halved to stand in for it.
- No answer covers the riveter the nose mounts on. Its dimensions are not compared.
- Tooling is listed per maker. A Cherry part gets Cherry's catalog rows, a Huck part gets Huck's. A third-party tool brand is listed apart with the rivet brands its own chart names.
- A Gage Bilt nose length read from its part number is used only where the chart that lists the nose prints that rule. It is shown as read from the part number, and it can only rule a nose out.
Next
Sources
- Cherry Fastening Systems for Aerospace Tool Catalog (©2015 edition, archived)
- Cherry CA-1001 Tool Catalog (2017)
- Cherry TS-H701B-456 instruction sheet (Rev E, 26 Jun 23)
- Cherry TS-H747-456 instruction sheet (Rev D, 26 Mar 15)
- Cherry CA-1015 (CherryMAX process manual)
- Gage Bilt Aerospace Catalog 2017 (archived; pages are PDF pages)