Low clearance puller finder
Enter the space you have, in inches. Each answer compares it with one dimension printed in the Cherry, Huck or Gage Bilt tool catalog. It is not a fit check of the whole tool.
CR3213-6-04, -6, 0.25 in to one wall
Printed dimension fits: 1 · Dimension not published: 8 · Does not fit: 1
"Printed dimension fits" means the one catalog dimension named is smaller than the clearance you entered. It covers that edge of the nose or head only. It does not cover the riveter the nose mounts on, the rest of the nose, the fastener's stem, stroke, hoses, your hand or anything the catalog does not dimension. The tool has to be tried in place before the job.
The aircraft's structural repair manual and the manufacturer's installation instructions govern. The tool manufacturer's data sheet governs the tool's dimensions.
Reference only: the controlling drawing, its process spec and the manufacturer's installation instructions govern. How to use these answers
Cherry tooling, for Cherry-made parts
6Right angle
- Side Centreline to edge: dimension not published.
- Head height, nose tip to back of head
- 2.25 in (printed 2-1/4") Cherry CA-1001 Tool Catalog p.6
- Fastener centreline to one edge of the nose
- dimension not published
On G704B, G704B-SR, G704B-40SH, G747, G800, G746A. On G83A, G84 with adapter 744-300. Cherry tool catalog 2015 p.26
Request this tool: buy, rent or repair →
OffsetThe nose mounts in line with the riveter. No document on file prints the riveter's length behind it.
- Side Centreline to edge: dimension not published.
- Nose length, in line with the riveter
- 3.3906 in (printed 3-25/64") Cherry CA-1001 Tool Catalog p.6
- Fastener centreline to one edge of the nose
- dimension not published
On G704B, G704B-SR, G704B-40SH, G747, G800, G746A. On G83A, G84 with adapter 744-300. Cherry tool catalog 2015 p.26
Request this tool: buy, rent or repair →- Side Centreline to edge: dimension not published.
- Nose length, in line with the riveter
- 4.5938 in (printed 4-19/32") Cherry CA-1001 Tool Catalog p.6
- Fastener centreline to one edge of the nose
- dimension not published
On G704B, G704B-SR, G704B-40SH, G747, G800, G746A. On G83A, G84 with adapter 744-300. Cherry tool catalog 2015 p.26
Request this tool: buy, rent or repair →
StandardThe nose mounts in line with the riveter. No document on file prints the riveter's length behind it.
- Side Centreline to edge 0.21 in (printed .21). 0.04 in to spare. End view: centreline to the flat on the nose. The side view draws the flat at the tip only and prints no length for it; behind it the nose is 3/4 in. diameter.
- Nose length, in line with the riveter
- 2.25 in (printed 2-1/4) Cherry TS-H701B-456 instruction sheet p.1
- Fastener centreline to one edge of the nose
- 0.21 in (printed .21) Cherry TS-H701B-456 instruction sheet p.1
On G704B, G704B-SR, G704B-40SH, G747, G800, G746A. On G83A, G84 with adapter 744-300. Cherry tool catalog 2015 p.26
Request this tool: buy, rent or repair →- Side Centreline to edge: dimension not published.
- Nose length, in line with the riveter
- dimension not published
- Fastener centreline to one edge of the nose
- dimension not published
On G784. Cherry tool catalog 2015 p.26
Request this tool: buy, rent or repair →- Side Centreline to edge 0.28 in (printed .28 EDGE DISTANCE AT FLATS). 0.03 in over. End view: centreline to the hex sleeve's flats. Across the corners the sleeve is wider.
- Nose length, in line with the riveter
- 2.3438 in (printed 2-11/32") Cherry CA-1001 Tool Catalog p.6
- Fastener centreline to one edge of the nose
- 0.28 in (printed .28 EDGE DISTANCE AT FLATS) Cherry TS-H747-456 instruction sheet p.1
On G704B, G704B-SR, G704B-40SH, G747, G800, G746A. On G83A, G84 with adapter 744-300. Cherry tool catalog 2015 p.26
Request this tool: buy, rent or repair →
Gage Bilt tooling. Gage Bilt's chart names Cherry, Allfast, Huck rivets
4Right angle
- Side Centreline to edge: dimension not published.
- Head height, nose tip to back of head
- 3.48 in (printed 3.48 (88.4 mm)) Gage Bilt catalog 2017 p.43
- Fastener centreline to one edge of the nose
- dimension not published
On GB704. Gage Bilt catalog 2017 p.43
Request this tool: buy, rent or repair →
OffsetThe nose mounts in line with the riveter. No document on file prints the riveter's length behind it.
- Side Centreline to edge: dimension not published.
- Nose length, in line with the riveter
- 4.312 in (printed 4.312) Gage Bilt catalog 2017 p.43
- Fastener centreline to one edge of the nose
- dimension not published
On GB704. Gage Bilt catalog 2017 p.43
Request this tool: buy, rent or repair →
StandardThe nose mounts in line with the riveter. No document on file prints the riveter's length behind it.
- Side Centreline to edge: dimension not published.
- Nose length, in line with the riveter
- 2.25 in (printed 2.25) Gage Bilt catalog 2017 p.43
- Fastener centreline to one edge of the nose
- dimension not published
On GB704. Gage Bilt catalog 2017 p.43
Request this tool: buy, rent or repair →- Side Centreline to edge: dimension not published.
- Nose length, in line with the riveter
- 3.5 in (not a printed number: read from the part number by the chart's note) Gage Bilt catalog 2017 p.41"The last 2 digits of the nose assembly represents the length the nose extends from the tool i.e. -20 = 2.0 inches" (note on this chart, PDF p.41). The same catalog draws 456MAX-701-17 at 1.75 in., so the rule is approximate.
- Fastener centreline to one edge of the nose
- dimension not published
On GB704. Gage Bilt catalog 2017 p.41
Request this tool: buy, rent or repair →
How the answer is worked outrules
- Right angle head: the catalog's head height, nose tip to back of head, is compared with your headroom. Where the catalog figure draws the tool body rising above that height with no dimension, the answer is "dimension not published".
- Straight or offset nose: it mounts in line with the riveter, and no catalog on file prints the riveter's length behind it. If the nose alone is as long as your headroom it does not fit. Otherwise the answer is "dimension not published".
- Side clearance: the catalog's centreline to edge dimension is compared with your distance to one wall. Most of these are drawn to one edge only, a flat or the offset edge of the head, and the note with each value says which. A nose diameter is never halved to stand in for it.
- No answer covers the riveter the nose mounts on. Its dimensions are not compared.
- Tooling is listed per maker. A Cherry part gets Cherry's catalog rows, a Huck part gets Huck's. A third-party tool brand is listed apart with the rivet brands its own chart names.
- A Gage Bilt nose length read from its part number is used only where the chart that lists the nose prints that rule. It is shown as read from the part number, and it can only rule a nose out.
Next