MS20470 solid rivet tooling, gauges and removal
generic-NAS · Solid rivet · Family page · Shop verification card · Get quotes for this tooling · Part number to tool, across brands
On the floor:Identify an aerospace fastener from its head and tail
By diameter
Tool: Rivet gun and bucking bar
Rivet gun and bucking bar, or squeeze. No tool part numbers are published in AC 43.13-1B for these rivets.
Tools, heads, adapters and gaugesCited tables
Rivet gun and bucking bar, or squeeze. No tool part numbers are published in AC 43.13-1B for these rivets.
Removal (drill-out)Published procedure
FAA AC 43.13-1B, Par 4-52 b (Disassembly Prior to Repairing)
- “When rivets are removed, undercut rivet heads by drilling. Use a drill of the same size as the diameter of the rivet. Drilling must be exactly centered and to the base of the head only.” FAA AC 43.13-1B, p.4-12, Par 4-52 b ↗
- “After drilling, break off the head with a pin punch and carefully drive out the shank.” FAA AC 43.13-1B, p.4-12, Par 4-52 b ↗
- “On thin or unsupported metal skin, support the sheet metal on the inside with a bucking bar.” FAA AC 43.13-1B, p.4-12, Par 4-52 b ↗
Cautions
- “Removal of rivet heads with a cold chisel and hammer is not recommended because skin damage and distorted rivet holes will probably result.” FAA AC 43.13-1B, p.4-12, Par 4-52 b ↗
Also published: FAA-H-8083-31B (AMT Handbook, Airframe), Removal of Rivets and Figure 4-98
- “File a flat area on manufactured head” FAA-H-8083-31B (AMT Handbook, Airframe), p.4-46, Figure 4-98 Rivet removal ↗
- “Center punch flat” FAA-H-8083-31B (AMT Handbook, Airframe), p.4-46, Figure 4-98 Rivet removal ↗
- “Drill through head using drill one size smaller than rivet shank” FAA-H-8083-31B (AMT Handbook, Airframe), p.4-46, Figure 4-98 Rivet removal ↗
- “Remove weakened head with machine punch” FAA-H-8083-31B (AMT Handbook, Airframe), p.4-46, Figure 4-98 Rivet removal ↗
- “Punch out rivet with machine punch” FAA-H-8083-31B (AMT Handbook, Airframe), p.4-46, Figure 4-98 Rivet removal ↗
Cautions
- “When a rivet has to be replaced, remove it carefully to retain the rivet hole’s original size and shape. If removed correctly, the rivet does not need to be replaced with one of the next larger size.” FAA-H-8083-31B (AMT Handbook, Airframe), p.4-44, Removal of Rivets ↗
- “When removing a rivet, work on the manufactured head. It is more symmetrical about the shank than the shop head, and there is less chance of damaging the rivet hole or the material around it.” FAA-H-8083-31B (AMT Handbook, Airframe), p.4-44, Removal of Rivets ↗
- “On thin metal or unsupported structures, support the sheet with a bucking bar while driving out the shank. If the shank is unusually tight after the rivet head is removed, drill the rivet about two-thirds through the thickness of the material and then drive the rest of it out with a drift punch.” FAA-H-8083-31B (AMT Handbook, Airframe), p.4-45, Removal of Rivets ↗
None of the removal procedures on file gives a composite-specific removal caution. The Monogram specs address composite at the hole instead: holes "reasonably round and free from burrs (metallic structure) and delamination (graphite/epoxy type structure)" (MBF2003 §5.1).
Sources
Tool tables are the manufacturer's as published in the cited revision; confirm current tool PNs with the manufacturer before purchase.
Reference only: the controlling drawing, its process spec and the manufacturer's installation instructions govern. How to use these answers
Next step
Free to ask. A person at SpecLok replies by email. You only pay the supplier if you accept a quote.
Tooling shop →Request installation training →MS20470 solid rivet part numbers →