◈SpecLok
  • Part number
  • Find a tool
  • Get quotes
  • Learn
More ▾

Learn

  • How specialty fasteners work
  • Explore fasteners
  • Catalog
  • AN / MS / NAS hardware
  • 3D model library
  • Compare side by side
  • Installation tooling guide
  • Design calculators
  • All articles

Select

  • Joint selector
  • Part-number decoder
  • Part-number cross reference
  • Which tool installs this part
  • Part-number index
  • Grip length planner
  • Hole schedule & grip review
  • BOM decoder

Quote and procure

  • Your quote
  • Request a tool: buy, rent or repair
  • Installation tooling
  • Preview the RFQ document
  • Your quote requests
  • Inventory and certs
  • The sourcing reality

Learn

  • How specialty fasteners work
  • Explore fasteners
  • Catalog
  • AN / MS / NAS hardware
  • 3D model library
  • Compare side by side
  • Installation tooling guide
  • Design calculators
  • All articles

Select

  • Joint selector
  • Part-number decoder
  • Part-number cross reference
  • Which tool installs this part
  • Part-number index
  • Grip length planner
  • Hole schedule & grip review
  • BOM decoder

Quote and procure

  • Your quote
  • Request a tool: buy, rent or repair
  • Installation tooling
  • Preview the RFQ document
  • Your quote requests
  • Inventory and certs
  • The sourcing reality

Aerospace Fasteners

SpecLok · a fastener-selection aid, not a certified design authority. Always verify against the controlling spec, OEM process, and your stress group.

Collects anonymous usage data to improve selection and sourcing. No personal info unless you add an email to a quote request.

Your account

← MS20470 solid rivet

Shop verification card

MS20470 solid rivet

generic-NAS · Solid rivet · MS20470 / AN470 · e.g. MS20470AD4-5

speclok.com
11/16/2026

Install sequence

  1. 1. Shank protrudes

  2. 2. Set and bucking bar

  3. 3. Shop head formed

Traced from FAA AC 43.13-1B, p.4-21, Figure 4-6. Not to scale.

Before you install

  • Diameters offered: 0.0625, 3/32, 1/8, 5/32, 3/16, 0.21875, 1/4, 5/16, 3/8"
  • Tool: Rivet gun and bucking bar
  • Standard shop tooling.
  • Training: Not stated in the cited documents.
  • Lead-time risk: Low

Installed preload

Not applicable: driven solid rivets are not preload-controlled fasteners (AC 43.13-1B).

Removal

Published: FAA AC 43.13-1B, Par 4-52 b (Disassembly Prior to Repairing). Removal of rivet heads with a cold chisel and hammer is not recommended because skin damage and distorted rivet holes will probably result. Steps: speclok.com/tooling/ms20470-solid#removal

Accept / reject after install

  • Shank protrusion before driving: 1.5D nominal (1D minimum).
  • Driven (shop) head: diameter 1.5D minimum; height 0.65D nominal (0.5D minimum) (AC 43.13-1B Fig 4-6(a)).
  • Reject per the Fig 4-6(c) defect chart: slanted rivet or bucking bar, flat-sided head, too-short body, rivet clinched between plates, bulged plates, over-driven head, tool-damaged plate, cracked head.

Check gauges

  • Driven-head dimensions measured directly (scale/calipers); rivet gauges are shop-made or commercial 1.5D/0.5D go-gauges.

Sources: FAA AC 43.13-1B, para 4-57 / Fig 4-6. Acceptance limits belong to the controlling spec: verify against your program's process documentation before use on hardware.

Sources

3
  1. MS20470H spec sheet + MIL-HDBK-5J Table 8.1.2(b)
  2. FAA AC 43.13-1B, para 4-57 / Fig 4-6
  3. FAA-H-8083-31B (AMT Handbook, Airframe)

Reference only: the controlling drawing, its process spec and the manufacturer's installation instructions govern. How to use these answers