Low clearance puller finder
Enter the space you have, in inches. Each answer compares it with one dimension printed in the Cherry, Huck or Gage Bilt tool catalog. It is not a fit check of the whole tool.
NAS1446, -6, 0.4 in to one wall
Printed dimension fits: 6 · Dimension not published: 5
"Printed dimension fits" means the one catalog dimension named is smaller than the clearance you entered. It covers that edge of the nose or head only. It does not cover the riveter the nose mounts on, the rest of the nose, the fastener's stem, stroke, hoses, your hand or anything the catalog does not dimension. The tool has to be tried in place before the job.
The aircraft's structural repair manual and the manufacturer's installation instructions govern. The tool manufacturer's data sheet governs the tool's dimensions.
Reference only: the controlling drawing, its process spec and the manufacturer's installation instructions govern. How to use these answers
Huck tooling, names the standard (any maker)
7OffsetThe nose mounts in line with the riveter. No document on file prints the riveter's length behind it.
- Side Centreline to edge 0.37 in (printed .37). 0.03 in to spare. Figure 4 draws C from the jaw centreline to the top edge of the head. It covers that one edge only; the head is B wide. 3/16" table
- Nose length, in line with the riveter
- 2.59 in (printed 2.59) Huck tool catalog 2010 p.50
- Fastener centreline to one edge of the nose
- 0.37 in (printed .37) Huck tool catalog 2010 p.50
On 244 with adapter 128279. On 245, 255 with adapter 119400-1, 118362. On 2480 with adapter 128279. Huck tool catalog 2010 p.46
Request this tool: buy, rent or repair →- Side Centreline to edge 0.37 in (printed .37). 0.03 in to spare. Figure 4 draws C from the jaw centreline to the top edge of the head. It covers that one edge only; the head is B wide. 3/16" table
- Nose length, in line with the riveter
- 3.4 in (printed 3.40) Huck tool catalog 2010 p.50
- Fastener centreline to one edge of the nose
- 0.37 in (printed .37) Huck tool catalog 2010 p.50
On 244 with adapter 128279. On 245, 255 with adapter 119400-1, 118362. On 2480 with adapter 128279. Huck tool catalog 2010 p.46
Request this tool: buy, rent or repair →
StandardThe nose mounts in line with the riveter. No document on file prints the riveter's length behind it.
- Side Centreline to edge 0.32 in (printed .32). 0.08 in to spare. Drawn from the centreline to the flat. The flat runs length D back from the tip; everywhere else the nose is diameter B. 3/16" table
- Nose length, in line with the riveter
- 1.85 in (printed 1.85) Huck tool catalog 2010 p.50
- Fastener centreline to one edge of the nose
- 0.32 in (printed .32) Huck tool catalog 2010 p.50
On 244, 2480. Huck tool catalog 2010 p.46
Request this tool: buy, rent or repair →- Side Centreline to edge 0.32 in (printed .32). 0.08 in to spare. Drawn from the centreline to the flat. The flat runs length D back from the tip; everywhere else the nose is diameter B. 3/16" table
- Nose length, in line with the riveter
- 4.35 in (printed 4.35) Huck tool catalog 2010 p.50
- Fastener centreline to one edge of the nose
- 0.32 in (printed .32) Huck tool catalog 2010 p.50
On 244, 2480. Huck tool catalog 2010 p.46
Request this tool: buy, rent or repair →- Side Centreline to edge 0.32 in (printed .32). 0.08 in to spare. Drawn from the centreline to the flat. The flat runs length D back from the tip; everywhere else the nose is diameter B. 3/16" table
- Nose length, in line with the riveter
- 2.2 in (printed 2.20) Huck tool catalog 2010 p.50
- Fastener centreline to one edge of the nose
- 0.32 in (printed .32) Huck tool catalog 2010 p.50
On 245, 255, 246, 256, 2502. Huck tool catalog 2010 p.46
Request this tool: buy, rent or repair →- Side Centreline to edge 0.32 in (printed .32). 0.08 in to spare. Drawn from the centreline to the flat. The flat runs length D back from the tip; everywhere else the nose is diameter B. 3/16" table
- Nose length, in line with the riveter
- 4.7 in (printed 4.70) Huck tool catalog 2010 p.50
- Fastener centreline to one edge of the nose
- 0.32 in (printed .32) Huck tool catalog 2010 p.50
On 245, 255, 246, 256, 2502. Huck tool catalog 2010 p.46
Request this tool: buy, rent or repair →- Side Centreline to edge: dimension not published.
- Nose length, in line with the riveter
- 4.35 in (printed 4.35) Huck tool catalog 2010 p.50
- Fastener centreline to one edge of the nose
- dimension not published
On 245, 255, 246, 256, 2502. Huck tool catalog 2010 p.46
Request this tool: buy, rent or repair →
Cherry tooling, names the standard (any maker)
2StandardThe nose mounts in line with the riveter. No document on file prints the riveter's length behind it.
- Side Centreline to edge: dimension not published.
- Nose length, in line with the riveter
- 2 in (printed 2" (Length from Tool Face column)) Cherry CA-1001 Tool Catalog p.10
- Fastener centreline to one edge of the nose
- dimension not published
On G83A, G84. On G87D, G85D-S with adapter 552. Cherry tool catalog 2015 p.32
Request this tool: buy, rent or repair →- Side Centreline to edge: dimension not published.
- Nose length, in line with the riveter
- 2.375 in (printed 2.375" (Length from Tool Face column)) Cherry CA-1001 Tool Catalog p.10
- Fastener centreline to one edge of the nose
- dimension not published
On G87D, G85D-S. Cherry tool catalog 2015 p.32
Request this tool: buy, rent or repair →
Gage Bilt tooling, names the standard (any maker)
2OffsetThe nose mounts in line with the riveter. No document on file prints the riveter's length behind it.
- Side Centreline to edge: dimension not published.
- Nose length, in line with the riveter
- dimension not published
- Fastener centreline to one edge of the nose
- dimension not published
On GB731 with adapter 751204. Gage Bilt catalog 2017 p.57
Request this tool: buy, rent or repair →
StandardThe nose mounts in line with the riveter. No document on file prints the riveter's length behind it.
- Side Centreline to edge: dimension not published.
- Nose length, in line with the riveter
- dimension not published
- Fastener centreline to one edge of the nose
- dimension not published
On GB731. Gage Bilt catalog 2017 p.57
Request this tool: buy, rent or repair →
How the answer is worked outrules
- Right angle head: the catalog's head height, nose tip to back of head, is compared with your headroom. Where the catalog figure draws the tool body rising above that height with no dimension, the answer is "dimension not published".
- Straight or offset nose: it mounts in line with the riveter, and no catalog on file prints the riveter's length behind it. If the nose alone is as long as your headroom it does not fit. Otherwise the answer is "dimension not published".
- Side clearance: the catalog's centreline to edge dimension is compared with your distance to one wall. Most of these are drawn to one edge only, a flat or the offset edge of the head, and the note with each value says which. A nose diameter is never halved to stand in for it.
- No answer covers the riveter the nose mounts on. Its dimensions are not compared.
- Tooling is listed per maker. A Cherry part gets Cherry's catalog rows, a Huck part gets Huck's. A third-party tool brand is listed apart with the rivet brands its own chart names.
- A Gage Bilt nose length read from its part number is used only where the chart that lists the nose prints that rule. It is shown as read from the part number, and it can only rule a nose out.
Next