◈SpecLok
  • Part number
  • Find a tool
  • Get quotes
  • Learn
More ▾

Learn

  • How specialty fasteners work
  • Explore fasteners
  • Catalog
  • AN / MS / NAS hardware
  • 3D model library
  • Compare side by side
  • Installation tooling guide
  • Design calculators
  • All articles

Select

  • Joint selector
  • Part-number decoder
  • Part-number cross reference
  • Which tool installs this part
  • Part-number index
  • Grip length planner
  • Hole schedule & grip review
  • BOM decoder

Quote and procure

  • Your quote
  • Request a tool: buy, rent or repair
  • Installation tooling
  • Preview the RFQ document
  • Your quote requests
  • Inventory and certs
  • The sourcing reality

Learn

  • How specialty fasteners work
  • Explore fasteners
  • Catalog
  • AN / MS / NAS hardware
  • 3D model library
  • Compare side by side
  • Installation tooling guide
  • Design calculators
  • All articles

Select

  • Joint selector
  • Part-number decoder
  • Part-number cross reference
  • Which tool installs this part
  • Part-number index
  • Grip length planner
  • Hole schedule & grip review
  • BOM decoder

Quote and procure

  • Your quote
  • Request a tool: buy, rent or repair
  • Installation tooling
  • Preview the RFQ document
  • Your quote requests
  • Inventory and certs
  • The sourcing reality

Aerospace Fasteners

SpecLok · a fastener-selection aid, not a certified design authority. Always verify against the controlling spec, OEM process, and your stress group.

Collects anonymous usage data to improve selection and sourcing. No personal info unless you add an email to a quote request.

Your account

← Eddie-Bolt 2

Shop verification card

Eddie-Bolt 2

Howmet/Huck · Pin and collar · EL… pin / EN… nut · e.g. EL1205NN8-6Y

speclok.com
11/16/2026

Install sequence

  1. 1. Nut started

  2. 2. Delta-Rad tool engaged

  3. 3. Lobes swaged into the flutes

Traced from Howmet Eddie-Bolt 2 process manual, p.17, Installation Sequence. Not to scale.

Before you install

  • Diameters offered: 5/32, 3/16, 1/4, 5/16, 3/8"
  • Tool: Delta-Rad driver (process manual)
  • Proprietary system required.
  • Training: Not stated in the cited documents.
  • Lead-time risk: Medium

Installed preload

Not published numerically. The process manual describes it qualitatively: torque is applied until "the required clamp load" is reached, at which point the nut lobes deform into the pin flutes to form the lock.

Gauge kit (published part numbers)

GaugeSizesChecks / limitsSource
EB2G1400allGrip gageHowmet Eddie-Bolt 2 process manual, p.16, Grip Gaging
EB2G1309allPin protrusion gageHowmet Eddie-Bolt 2 process manual, p.20, Inspection Information
EB2G1000 / EB2G1100 / EB2G1200allPaddle or Thimble type gageHowmet Eddie-Bolt 2 process manual, p.22, Inspection Gage Information
EB2G2000-( ) / EB2G2100-( )allTool wear gageHowmet Eddie-Bolt 2 process manual, p.28, Installation Tooling

Removal

Published: Howmet Eddie-Bolt 2 process manual, Removal Procedures. Removed Eddie-Nuts shall not be reused and Eddie-Pins must be replaced before installing a new Eddie-Nut. Steps: speclok.com/tooling/eddie-bolt-2#removal

Accept / reject after install

  • Pin protrusion checked with gage EB2G1309: pin must sit between the MIN and MAX cutouts, checked after nut installation with no gaps between structure components.
  • Nut swage conformity: a Paddle (EB2G1000) or Thimble (EB2G1100/1200) gage must pass completely over the deformed lobes.
  • Head seating: a .002" feeler gage must not enter to the shank.
  • No rework: incomplete swage or a spinning pin means remove and replace both pin and nut; re-swaging is not permitted. Shaving flush heads is not permissible.

Check gauges

  • EB2G1309 pin protrusion gage.
  • EB2G1000 Paddle / EB2G1100 and EB2G1200 Thimble swage gages.
  • EB2G1400 grip gage (pre-install); EB2G2000/2100 driver-wear gages.

Sources: Eddie-Bolt 2 process manual (Howmet). Acceptance limits belong to the controlling spec: verify against your program's process documentation before use on hardware.

Sources

1
  1. Howmet Eddie-Bolt 2 process manual

Reference only: the controlling drawing, its process spec and the manufacturer's installation instructions govern. How to use these answers