◈SpecLok
  • Part number
  • Find a tool
  • Get quotes
  • Learn
More ▾

Learn

  • How specialty fasteners work
  • Explore fasteners
  • Catalog
  • AN / MS / NAS hardware
  • 3D model library
  • Compare side by side
  • Installation tooling guide
  • Design calculators
  • All articles

Select

  • Joint selector
  • Part-number decoder
  • Part-number cross reference
  • Which tool installs this part
  • Part-number index
  • Grip length planner
  • Hole schedule & grip review
  • BOM decoder

Quote and procure

  • Your quote
  • Request a tool: buy, rent or repair
  • Installation tooling
  • Preview the RFQ document
  • Your quote requests
  • Inventory and certs
  • The sourcing reality

Learn

  • How specialty fasteners work
  • Explore fasteners
  • Catalog
  • AN / MS / NAS hardware
  • 3D model library
  • Compare side by side
  • Installation tooling guide
  • Design calculators
  • All articles

Select

  • Joint selector
  • Part-number decoder
  • Part-number cross reference
  • Which tool installs this part
  • Part-number index
  • Grip length planner
  • Hole schedule & grip review
  • BOM decoder

Quote and procure

  • Your quote
  • Request a tool: buy, rent or repair
  • Installation tooling
  • Preview the RFQ document
  • Your quote requests
  • Inventory and certs
  • The sourcing reality

Aerospace Fasteners

SpecLok · a fastener-selection aid, not a certified design authority. Always verify against the controlling spec, OEM process, and your stress group.

Collects anonymous usage data to improve selection and sourcing. No personal info unless you add an email to a quote request.

Your account

← Blind rivet nut (MS27130, now NAS1329 / NAS1330)

Shop verification card

Blind rivet nut (MS27130, now NAS1329 / NAS1330)

generic-NAS · Blind rivet nut · MS27130-[material][dash][K] · e.g. MS27130-A26K · superseded by NAS1329 (flat head) / NAS1330 (countersunk head)

speclok.com
11/16/2026

Install sequence

  1. 1. On the mandrel

  2. 2. In the hole

  3. 3. Mandrel retracts, body expands

  4. 4. Installed, ready for a screw

Traced from US 2,149,199 (Tubular rivet, B. F. Goodrich), p.1 (drawing sheet), Figs. 1-3, 6. Not to scale.

Before you install

  • Sizes offered: .112-40UNC-3B to .500-20UNF-3B (MS27130F Tables I and III)
  • Tool: Pull-up tool with a threaded mandrel (Rivnut hand or power tools)
  • Special, non-proprietary tooling.
  • Training: Not stated in the cited documents.
  • Lead-time risk: Medium

Installed preload

Not published. MS27130F gives minimum tensile and single shear strength (Table V) only; FAA-H-8083-31B and the Böllhoff RIVNUT catalog give no preload.

Removal

No published removal procedure found; follow the manufacturer's instructions. Steps: speclok.com/tooling/blind-rivet-nut#removal

Accept / reject after install

  • "Correct installation requires good hole preparation, removal of burrs, and holding the sheets in contact while heading. Like any sheet metal fastener, a rivet nut should fit snugly into its hole." (FAA-H-8083-31B p.4-56)
  • Install hole, MS27130F Table II (flathead), min-max: .112: .155-.157 (drill 5/32); .138: .189-.193 (#12); .164: .221-.226 (#2); .190: .250-.256 (E); .250: .332-.338 (Q).
  • Grip: the dash number sets the grip range and ident mark (MS27130F Tables I and III); "The part number identifies the type of rivet nut and the maximum grip length." (FAA-H-8083-31B p.4-55)
  • Keyed nuts (K) go in a keyway cut to the Keyway Detail (MS27130F Table II, P and H).

Check gauges

  • No inspection gauge is named in the documents read.

Sources: MS27130F · FAA-H-8083-31B p.4-55 to 4-56. Acceptance limits belong to the controlling spec: verify against your program's process documentation before use on hardware.

Sources

2
  1. MS27130F (Nut, plain, blind rivet, flat and countersunk head, open end)
  2. FAA-H-8083-31B p.4-55 to 4-56

Reference only: the controlling drawing, its process spec and the manufacturer's installation instructions govern. How to use these answers